bgp routing protocol

Networking requirements:1. AS65000 boundary network segment release: RT1 and RT2 re-release direct connection route to OSPF (metric 1000 type 1)2. BGP Configuration Requirements:No synchronizationNo auto-summary IBGP uses LOOPBACK to establish a neighbor, and the next hop points to itself3. RT1 and RT2 publish a summary route of AS65000 to BGP: 10.0.0.0/16 and 10.3.0.0/16.4. RT5 publishes a summary route fo

BGP routing load balancing fault caseNetwork Architecture 1. Topology: the actual network structure is simplified considering the privacy of the company's network and a clearer description of fault phenomena. 2. network planning and data Configuration Overview: ◆ ASR9K establishes IBGP neighbor relationships with two n7ks Based on the interconnected addresses respectively; ◆ ASR9K is connected to the Cisco

Today, we gave a client a test report based on Route-map to filter through different routes to different end-to-end Cross-domain neighbors. The function point is very small, but for the junior students want to help. BGP is actually a very powerful routing protocol for routing filtering. CCIE is also the focus of the

Key Issues 1) How does an ACL match route entries with the same subnet and different masks? How do I match entries with the same mask and different subnets? 2) Why does a summary route cause a tumble of BGP peers? 3) Why does the acl fail to match the route entry when attribite-map is used? 4) How to Use advertise-map, suppress-map, unsuppress-map, attribute-map, and route-map routing diagrams? Instance. 5)

generate the most reasonable path (merge ). (The basic logic of RIP is: if A is 6 away from B and I am 1 Away From A, the distance from A to B is 7) For technical reasons (looping hops), rip considers that IP addresses over 15 cannot arrive. Therefore, rip is more used in the Internet (such as the entire China Telecom Network ). Such an internet part often belongs to the same ISP or has the same management organization, so it is called an autonomous system (as, autonomous system ). Hosts and

Summary of configuration formats of dynamic routing (ripV2, ospf, VPN, bgp, IS-IS)1. r12002router rip enable rip Protocol no atuo-summary disable automatic summary of version 2 2 network x mask x declaring the network segment (the subnet mask is a positive mask, mask can be disabled. 2. Enable the ospf protocol for osp

First, the experimental topology:Second, the experimental requirements:1, R4, R1, R3, R2 respectively in the BGP process deployment neighbor Send Community attribute command;2, R4 deployment ACL crawl 4.4.4.4 traffic, Route-map named as, call ACL, set community Local-as, and call Route-map as out in the BGP process;3, verify: R1, R3 have 4.4.4.4, but R2 have no 4.4.4.0 route entry?Third, command deployment:

* BGP is designed to process a large number of Route entries.Control the bandwidth traffic in a certain transmission direction.1. Controllable attributes:· Local priority:It is valid for outbound traffic.Relatively speaking, it is a priority.· MED multi-exit identification:Injected by external EBGP, It is set by the Administrator outside of AS to affect this.To effectively control the traffic that leaves me.· Weight2. Control through route ingThe

First, the experimental topology:Second, the experimental requirements:1, R4, R1, R3, R2 respectively in the BGP process deployment neighbor Send Community attribute command;2, R4 deployment ACL crawl 4.4.4.4 traffic, route-map named PL, call ACL, set community no-advertise, and invoke Route-map pl out in the BGP process;3. Verify: View R1 in 4.4.4.4 Item details Are you carrying: no-advertise, and do not p

In the network structure, we have been paying attention to their deployment and optimization. As the network pressure increases, we have put forward higher requirements for some hardware and protocols. Now, we will focus on the deployment of BGP routing protocols. In general, the BGP routing

BGP Extended Communities for OSPF PE-CE Routing-domain ID analysis to make OSPF Routing characteristics can pass through the mpls vpn backbone network, it needs to define some BGP Extended group attributes. OSPF attributes that can be passed through mp bgp include:The extend

First, the experimental topology:Second, the experimental requirements:1, increase R5:as 5, and R2 through the Direct Connect route to establish BGP neighbor relationship;2, R2 deployed in BGP under Send-conmmunity to R5;3, R4 deployment ACL crawl 4.4.4.4 traffic, Route-map named Shuchu, call ACL, set community no-export, and invoke Route-map Shuchu out in the BGP