it to work. This was because Modemmanager can be quite forceful by locking device ports. Alternatively, you can switch the device using SAKIS3G (at which point Network Manager should pick it up) and then connect ing using Network Manager.
As for the Pin-either remove the required pin from the SIM card by putting it in a normal mobile phone or provide your P In for switching in/etc/sakis3g.conf using the sim_pin= "" variable.
Reference:http://web.archive.org/web/20120908202215/http://wik
By Sreekrishnan Venkateswaran
Linux Bluetooth
Bluetooth is a short-range wireless technology used to replace cables. It supports 723 kbps (asymmetric) and 432 kbps (symmetric) speeds to transmit data and voice. The transmission range of a Bluetooth device is about 10 meters (30 feet ).
BlueZ is the official
Linux wireless network technology series II Bluetooth (1)
By sreekrishnan venkateswaraPosting time: 2004.12.30
BlueZ 是官方 LinuxBluetooth 栈,由主机控制接口(Host Control Interface ,HCI)层、Bluetooth协议核心、逻辑链路控制和适配协议(Logical Link Control and Adaptation Protocol,L2CAP)、SCO 音频层、其他 Bluetooth 服务
(hci_dev_info). Among them, flags explained very easily at the time. In fact, it stores a bluetooth device (for example, USBBluetooth dongle) Current status:
The "up" and "down" statuses indicate whether the device is started. You can use IOCTL (hcidevup) to modify these statuses.
In addition:Inquiry scan, pageScanThese statuses:
When Sam started his own L2CAP layer connection, he used another
think that the Linux protocol stack is inferior to the one in Windows. The fact is that the scenery here is good, and the bluez protocol stack supports far more hardware devices than windows systems. If you only use Linux like me, after buying the Bluetooth adapter, you will probably be able to drop the bloated drive disc into the trash, and then use the
Terminal HC-05" to connect to the Working Bluetooth module.Find the Bluetooth module named Tele and input password 1234(By default password is 0000 or 1234)Open app "Bluetooth Terminal HC-05" Select CR(carriage Return), LF (line Feed).Connect the Bluetooth module with the Usb
to activate your USB deviceB. hciconfig hci0 up-- This step is to activate your USB Bluetooth Dongle (USB Bluetooth adapter)C. hcitool Dev-- Check whether your adapter is correctly identified and working properlyD. Adjust your mo
How to use Bluetooth under Linux
Bluetooth is a wireless protocol chosen by many mobile device manufacturers, and it is a short-range wireless transmission technology. It has a number of attractive features, the most important of which is its low energy consumption in data transmission. Currently there are three versions of the
Linux does not recognize Bluetooth adapter solutions
Bluetooth adapter (USB): Wins for UDC-321Linux 2.6.29First check to see if USB is recognized:#lsusbBus 005 Device 004:id 0402:5602 ALi Corp., Camera ControllerBus 005 Device 003:id 05e3:0718 Genesys Logic, Inc.Bus 005 Devi
, respectivelyYes: controller drivers, Gadget drivers, and upper layers.
I. Controller (USB device controller, UDC) Driver
The Gadget Framework proposes a set of standard APIs. At the underlying layer, the USB device controller driver implements this set of APIs. Different UDC requires different drivers and evenCode modifications are also required for different boards based on the same UDC. This layer is re
1. Activating the device
The first thing to have is a Bluetooth adapter, which, needless to say, is typically a USB interface type.
Lsusb View the Bluetooth devices connected in the system
hciconfig View the details of the device
Hciconfig hci0 up to activate the device
2. Configure BlueZ
Configuration file is located in directory/etc
Use Bluetooth in Linux
Today we will introduce how to use Bluetooth through commands in Linux:
Because my laptop does not have bluetooth, I bought a Bluetooth adapter for the USB inte
This story uses kernel code 2.6.22. In the Linux kernel code directory, all the Code related to the device driver is under the drivers/directory. Using the ls command in this directory, you can see many subdirectories:
Lfg1:/usr/src/linux-2.6.22/drivers # ls
Kconfig acpi atm block char cpufreq dma fc4 hid ide
Input leds md mfd mtd oprofile pci ps3 s390 serial spi
Us
This story uses kernel code 2.6.22. In the Linux kernel code directory, all the code related to the device driver is under the drivers/Directory. Using the ls command in this directory, you can see many subdirectories: lfg1: /usr/src/linux-2.6.22/drivers # lsKconfi...
This story uses kernel code 2.6.22. In the Linux kernel code directory, all the code related to
and compile your kernel, and select M for the modules that are added to the Bluetooth part. If you are not sure which one is useful or useless.
Install the downloaded package one by one after completing the kernel, in the order of my list. Simple
./Configure make install.
Now we can R R
First load the kernel module:
Modprobe bluez (supported by bluetooth)
Modprobe hci_usb (for
DebianLinux Uses Bluetooth to communicate with mobile phones-Linux Release Technology-Debian information. See the following for details. Use Ericsson T68i, Sony Ericsson T628, and Billionton USB Bluetooth Adapter to pass the test in the Debian Kernel-2.6.0 Kernel.
(I purchased Billionton
: ID 1d6b:0001 Linux Foundation 1.1 root hubBus 002 Device 003: ID 17ef:4811 Lenovo Integrated Webcam [R5U877]Bus 008 Device 002: ID 0a5c:217f Broadcom Corp. Bluetooth Controller
Lsusb will display the driver and the device that is internally connected to your system.
The following describes how to understand the output. I captured the last line output above:
Bus 008 Device 002 : ID 0a5c:217f Broadcom Corp.
GPS + Bluetooth + Linux Mobile Positioning-Linux Enterprise Application-Linux server application information. The following is a detailed description. Source http://blog.sina.com.cn/s/blog_4aedf42a01007wyy.html
Author: GuanweiYu pluto_caesar [AT] yahoo.com.cn
After an afternoon, I finally figured it out. I checked th
For more information about the HCI specification, see First, we need to understand that the host part of HCI is implemented on Linux.1. Related Data Structure 1.1 Hci_devIn Linux, Hci_dev is used to represent an HCI Host (corresponding to a control)
Members
Role
Char Name[8]
Bluetooth name
__u8 Bus
HCI
transmitted.BintervalIf the endpoint is of the interrupt type, this value is the interval setting of the endpoint, in milliseconds.Logically, functions of a USB device are divided by interfaces. For example, a USB speaker may have two interfaces: one for keyboard control and the other for audio stream transmission. In fact, this type of device requires two different drivers to operate, one controlling the
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.