broadcom bluetooth

First, make sure you are a bit ldquo; Lucky Winner rdquo;:/sbin/lspci | grepBroadcom0b: network00.0 controller: broadcomconfigurationbcm4312802.11a/B/g (rev01) install the required components: First, make sure you are the lucky guy with the Broadcom BCM43xx wireless network card ": /Sbin/lspci | grep Broadcom 0b: 00.0 Network controller: Broadcom C

The Local Wireless NIC driver cannot be installed, which is inconvenient. After reading a lot of information, Dell and Broadcom do not provide drivers for Linux. The existing drive is b43, refer to http://linuxwireless.org/en/users/Drivers/b43 However, the instructions are not in English, and the installation method above finally encountered a problem. Khan ~~~~~~~~ It's just not done ............. That's all. I carefully checked my Nic chip

Source: qiuyi21.cnblogs.com1 , download the latest official version of the driverOn Broadcom official website http://www.broadcom.com/support/ethernet_nic/downloaddrivers.php Download the latest official version of the driver for your network card, do not download the beta version.2 , delete the system's own driver cacheAt the same time press the WIN + x appear management menu, then press g Key to open Computer Management, left check "Device Manager",

Provides its own message mechanism in Broadcom, with two message forms: Request/response and Event(event)request/response Message: the communication between the process is through the SMD, all the messages are sent to the SMD,SMD after receiving the information, if the message is to be SMD to do the corresponding operation, if not, the message route outEvent messages: a process that is interested in certain events can cms_msg_register_event_interest r

crab, Found on the sourceforge of its SDK (rtl819x-sdk-v3.2.3), but also Ap/router Soc program, interested can come down to see, Address: Http://sourceforge.net/projects/rtl819x/?source=directory Broadcom Platform To change to this platform, this platform's SDK data is relatively small, but still found a trace, ASUS Rt-n16 has open source on Google Code, Rt-n16 is Broadcom BCM4716 Address: https://code.go

First, installed under UbuntuThis does not have to be installed, the system is well supported.System->administration->hardware DriversChoose the Broadcom STA wireless driverActivateIf you do not have this option, execute it in the shell:sudo apt-get updatesudo apt-get--reinstall install bcmwl-kernel-sourceAfter restarting, repeat the previous step to activate the driver. I tested the Chinese version of Ubuntu14.04 and found that this driver was not in

The configuration of the broadcom wireless network card under Debian4.0r0-Linux Release Technology-Debian information. The following is a detailed description. It should be said that debian has evolved to 4.0r0, and his desktop system has become perfect. I had been using Ubuntu 6 since 3.3, but it was intolerable, but now it turns back and finds that 4.0r0 and ubuntu have no special difference and are more stable. I often encounter conflicts and error

First, the configuration of the port group in the actual situation of the use of many scenarios, partial redundancy mainly to solve the single point of failure. Many are in combination with Ha, VRRP, HSRP, switch stacking and many other practical scenarios.All right, no nagging, just "meal".The first step:Configuration Broadcom NIC Group to broadcom network card Group is enabled on the NIC, need to be inst

Today, when I build Broadcom 802.11 Linux STA driver, there is a error: src/wl/sys/wl_linux.c: 388: 2: error: unknown field 'ndo _ set_multicast_list 'specified in initializer then I google this question and find its answer. 1 vim src/wl/sys/wl_linux.c go to line 385: change the line :. ndo_set_multicast_list = wl_set_multicast_list, to the line :. ndo_set_rx_mode = wl_set_multicast_list, 2 make then you will find everything OK. here is the output lin

sudo cp ssb-sprom/usr/sbin/ sudo chmod 755/usr/sbin/ssb-sprom sudo chown root:root/usr/sbin/ssb-sprom ssb_sprom=$ (Find/sys/devices-name ssb_sprom) Echo $SSB _sprom CD ~ sudo cat $SSB _sprom > Ssb_sprom_copy Ssb-sprom-i ssb_sprom_copy-p Ssb-sprom-i ssb_sprom_copy--subv 0x106b--subp 0x004e--ccode cn-o new_ssb_sprom_copy Ssb-sprom-i new_ssb_sprom_copy-p Echo $SSB _sprom sudo cp new_ssb_sprom_copy $SSB

Updates It can be found that the Devel package is only 2.6.32-504, this package will not compile properly for 2.6.43-358 driver, so my environment cannot be used. can go to http://rpm.pbone.net/website Search kernel-devel-2.6.32-358 Package, if your kernel version and my not the same please search for their own package 4, download the driver srpm package 4.1 Download the latest driver from official website netxtreme ii 5716, this dr

Http://archive.cnblogs.com/a/2209414/fedora System Using Broadcom bcm4312 wireless network adapter After the fedora system is installed (, 15), The Broadcom bcm4312 wireless Nic cannot be used. You can enable the wireless Nic using the following methods! I use the first one ~1. Use the kernel module b43 + firmware to drive the bcm4312 wireless Nic After the fedora system is installed, there are b43 modules,

[Root @ localhost ~] # Rpmbuild-bb tg3.spec[Root @ localhost ~] # Cd/usr/src/redhat/RPMS/x86_64[Root @ localhost ~] # Rpm-ivh tg3-3.133d-1.x86_64.rpm 3. Load modules[Root @ localhost ~] # Modprobe tg3[Root @ localhost ~] # Vim/etc/modprobe. confAlias eth0 tg3Alias eth1 tg3Alias eth2 tg3Alias eth3 tg3 4. Restart the server and the NIC will be displayed. RHEL6.4 install the Broadcom BCM4313 wireless NIC Driver The B