broadcom nic card

First, the configuration of the port group in the actual situation of the use of many scenarios, partial redundancy mainly to solve the single point of failure. Many are in combination with Ha, VRRP, HSRP, switch stacking and many other practical scenarios.All right, no nagging, just "meal".The first step:Configuration Broadcom NIC Group to broadcom network

Http://archive.cnblogs.com/a/2209414/fedora System Using Broadcom bcm4312 wireless network adapter After the fedora system is installed (, 15), The Broadcom bcm4312 wireless Nic cannot be used. You can enable the wireless Nic using the following methods! I use the first one ~1. Use the kernel module b43 + firmware to d

A few days ago, the company purchased a new server, DELL R720. After installing and installing CentOS 5.6, it found that only lo exists and there is no eth * Nic, after several queries, rhel5.x or centos 5 was installed for newer machines such as r620 and r720. x system, without its NIC driver, so we need to install it ourselvesNIC Driver, http://zh-cn.broadcom.com/support/ethernet_nic/downloaddrivers.phpWe

Ubuntu1310lenovo NIC driver installation (Broadcom) ubuntu has just released version 1310 this month. after upgrading the operating system version, it cannot search for wireless hotspots. drivers downloaded from Lenovo's official website are all for windows, therefore, you have to find the linux driver corresponding to the NIC. Run the following ubuntu 13.10 vers

Install the Broadcom wireless NIC Driver on CentOS 7 First, make sure you are the lucky guy with the Broadcom BCM43xx wireless network card ": /Sbin/lspci | grep Broadcom 0b: 00.0 Network controller: Broadcom Corporat

First, installed under UbuntuThis does not have to be installed, the system is well supported.System->administration->hardware DriversChoose the Broadcom STA wireless driverActivateIf you do not have this option, execute it in the shell:sudo apt-get updatesudo apt-get--reinstall install bcmwl-kernel-sourceAfter restarting, repeat the previous step to activate the driver. I tested the Chinese version of Ubuntu14.04 and found that this driver was not in

Ubuntu13.10 Lenovo NIC Driver Installation (Broadcom) Ubuntu has just released version 13.10 This month. After upgrading the operating system version, it cannot search for wireless hotspots. Drivers downloaded from Lenovo's official website are all for Windows, therefore, you have to find the Linux driver corresponding to the NIC. Run the following command: comma

Ubuntu13.10 lenovo NIC Driver Installation (Broadcom) ubuntu has just released version 13.10 This month. After upgrading the operating system version, it cannot search for wireless hotspots. Drivers downloaded from lenovo's official website are all for windows, therefore, you have to find the linux driver corresponding to the NIC. Run the following Command: Comma

b43 14e4: 4312 Not Supported-ID is duplicated Bcm4312 B/g G B43 My Nic is B/g, but a/B/g is supported. I don't know if my understanding is correct ~~~~ All of them are of the 4312 model, so complicated ..... At last, I accidentally found that my wireless network card was actually equipped with a driver, but it was not correct. Search for

First, make sure you are a bit ldquo; Lucky Winner rdquo;:/sbin/lspci | grepBroadcom0b: network00.0 controller: broadcomconfigurationbcm4312802.11a/B/g (rev01) install the required components: First, make sure you are the lucky guy with the Broadcom BCM43xx wireless network card ": /Sbin/lspci | grep Broadcom 0b: 00.0 Network controller:

the instructions, and installed the system Happily. The system was stuck on the system installation loading interface--|, I was thinking, which of the following is my mistake, but the network gets stuck at this time,Google cannot open, just a few days ago a linux deepinSo I figured it out. I tried to install it. everything went fine. after the installation, the interface was very beautiful, and there were a lot of supported application software, which was not so difficult. But the problem is...

? You can directly plug in the network cable and install something in the wired network environment. Then I find the root network cable, plug it in, or cannot connect to the network. In the end, I was so bold and confused! Done! Start: First, check the model of your Nic and enter the command lspci on the terminal. You can see your Nic model, for example, my network ca