Configuration of brocade 300 optical fiber switch, brocade 300 optical fiber switchI. Mounting1. New Fiber Optic Switches are availableNote that the network port and Management port are different2. wiredIi. basic configuration1. C
I have previously reprinted an article about port activation of the brocade San optical fiber switch. You only need to use a direct connection to connect the NIC AND THE brocade switch.The IP address of the computer is set to 10.77.77.0. Enter the default IP address 10.77.77.77 in the browser to directly configure the
Document directory
1. Collect the WWN address of the SAN Switch:
2. It takes 5 steps to register licnese from the official brocade website.
3. Import the license key:
Technorati labels: brocade, brocade, San, optical fiber switch
Configuration and management of brocade optical fiber switch (B/S)
This article uses the Brocade 300 optical fiber switch as an example.
The default IP address of the brocade
Configuration of brocade 300 optical fiber switchI. Mounting1. New Fiber Optic Switches are availableNote that the network port and Management port are different2. wiredIi. basic configuration1. Configure IP address and Change User PasswordA. The default ip address of the new optical fiber
zone
A. "manage" refers to "zone admin" refers to "zone", which is divided according to alias, name format: "server name_corresponding HbA _ storage name_corresponding to port 0 controller _ corresponding to Port 1 controller"
B. Add a zone based on Alias
When creating a zone, you need to add the alias of the host hosts card and the stored alias to the same zone.
3. Create zone config
A. "manage" refers to "zone admin" refers to "zone config"
B. Use the default configure, select the created
View Optical fiber type# lspci| grep Fibre1. NHB Nicholas Fiber Card brocade/sys/class/fc_host See if the optical fiber card is loaded, if not, Brocade_adapter_software_installer_linux_v2-3-0-3.bin (use the graphics interface to install VNC./Brocade_adapter_software_installer_linux_v2-3-0-3.bin)2. NHA Nicholas HP Optic
Set the IP address of the Brocade switch. The default IP address of the Brocade switch is 10.77.77.77. In command line mode, you can use the ipaddrset command to set and modify the IP address of the switch www.2cto.com swd77: admin> ipaddrsetEthernet IP Address [10.77.77.77]
This article is illustrated with the Brocade 300 fibre switch.The default IP address for brocade switches is 10.77.77.77, username admin, password: password.1 , Login management interface (1) ip address " 10.77.77.** (subnet mask ) 255.0.0.0 650) this.width=650; "title=" brocade fibre switch configuration and
Cause:The unit bought two storage, two brocade fibre switches, several servers, and Oracle RAC.But the brocade fibre switch has requirements for the Java version, I tried Java 7.X, Java 8.X, Java 6.0X, Java 6.3X, can not be opened with the Web. (although it can be configured with the command line, I don't want to learn the order in order to draw a zone.) )Finally
Brocade Brocade300 Fibre SwitchBrocade switches: Fibre Channel port : Switch mode ( default ): 24 ports that can be enhanced by on-demand port licenses to 8 port increments to 8 16 and 24 generic (E, f, m, fl or N) port , Access Gateway default port mapping: 16 f_port 8 N_port Scalability: fully fabric architecture with up to 239 switchesStandard Maximum Support number : single
Brocade 300 optical end switch zone division we are here the brocade optical end switch, in fact, the manufacturers are the same, where is the principle, according to the principle and architecture to divide the zone. Of course, the graphic interface Division is also simple. Fabric OS (WOLFB300SWA) implements Fabos Ver
The brocade switch is widely used as the more affordable fiber switch, and the Zone division is an important function, the common method has character interface and graphical interface. Here's a brief introduction:
The command flow is:
Alicreate
When creating a zoning configuration, you should first create an alias
Huawei Optical Fiber switches improve performance through the optical fiber expansion module. Colleagues are responsible for the interconnection of Huawei Optical Fiber switches in the company. This is a very large project. Outsiders will be confused. The following are just some of the issues with Huawei Optical Fiber
Steps:1. Run first, porterrshow view port status, then ' Statsclear ' and ' slotstatsclear '2. View: Porterrshow, look at the port.3. Collection of Supportshow, Supportsave4. View Sfpshow-all can see the second-to-last line of 23 Rx power status, if larger is normalSfpshow-all:=============Port 0:=============Identifier:3 SFPConnector:7 LCtransceiver:540c402000000000 200,400,800_mb/s m5,m6 SW inter_distEncoding:1 8B10BBaud rate:85 (Units Megabaud)Length 9u:0 (units km)Length 9u:0 (Units-meters)L
CISCO mds FC optical fiber switch configuration reference(1) There are several concepts that must be clarified (different from brocade ):(1) brocade divides zones directly. While mds divides zones under vsan, mds can divide several vsan first, and each vsan includes several zones.(2) brocase: the default port is open,
"configuration file name ". For example, cfgEnable "cfgTechSales" 5. The command to save the configuration file on 2109 is "Save save. In this way, we have configured the partition (Zoning) on IBM 2109 ). You can run the ZoneHelp command on the vswitch to view other command information about partition configuration. **************************************** * ***************** Brocade 4 Gb SAN Switch (for H
Vswitch Optical Fiber ports are divided into many types, and their functions are quite different. Here we will mainly introduce some basic knowledge about common optical fiber ports of vswitches. Cascade uses both common ports and special MDI-II ports. A straight-through cable should be used when the two ports that are cascaded are normal ports (MDI-X) ports and MDI-II ports, respectively. Cross-cable shoul
product may require the following key technologies and performance: high reliability, high-end port density, service quality assurance and other functions. The Fibre-optic Ethernet business is more cost-effective than other broadband access, but so far it has been used only in office buildings or in buildings where fibre optics have been laid. The strategic value of this new method of using Ethernet is not limited to cheap access. It can be used both for access networks and for local backbone
1. Introduction
To achieve non-blocking communication on the existing 100,000-kilometer high-speed trunk cable network, the operator must first consider how to implement automatic protection of optical transmission physical routes. The optical fiber automatic switch protection system is an automatic monitoring and protection system that integrates monitoring, protection, and management. It is independent of
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.