network in the first phase of construction, the backbone of the use of ATM technology, installed a certain number of network equipment, the backbone of the switch using the 3COM corebilder 7000HD, the current equipment is working normally. In the second phase of construction, the backbone of the use of Gigabit Ethernet technology, in order to protect the campus network Phase I Project investment, the original ATM and Gigabit Ethernet interface between the following several ways: (learning compu
example of a speed limit of 6500:
Mls QoS aggregate-policer Test 50000000 100000 conform-action transmit exceed-action drop
Mls QoS
Class-map Match-any Test_limite
Match Access-group name Test_addr
Policy-map Rate-limit-uplink
Class Test_limite
Police aggregate test
IP Access-list Extended test_addr
Permit IP any x.x.x.x 0.0.0.255
Inter G0/1
Service-policy input Rate-limit-uplink
Summary: Cisco switch port speed limit commonly used configuration, the front-end speed limit work is done by the su
original network equipment, the connection between the ATM and Gigabit Ethernet networking technologies is involved, this article introduces the solution to this problem based on our practical experience.
During the Phase I project construction of our campus network, the backbone uses the ATM technology and installs a certain number of network devices. The backbone switch uses the 3COM Corebilder 7000HD, which currently works normally. In the phase II project construction, the backbone adopts t
of G.703-ETH bridge converter for access, the price is equivalent to G/V converter, therefore, with the new network access solution, the larger the scale, the more nodes that are connected to the downlink, the more cost savings.
When the center end of the uplink uses a layer-3 Switch for access, the downlink branch node does not need any grade router, only need to be equipped with a hub or switch and G.703-ETH bridge converter, about 10 thousand yuan.
1. Port density and scalability No matter w
In the composition of wireless networks, the use of many devices deserves a detailed understanding. Today we will talk about the failure of VLAN wireless Internet access switches. The following is an experience shared by a netizen: A strange problem occurs in the VLAN of the two departments where an office area is located. Some websites on the Internet can be accessed normally, but some websites cannot; emails received through Outlook or Foxmail are normal, and small emails without attachments a
The topology is as follows:
1. Catalyst 6509 Switch configuration Scheme1.1 configure Layer-2 switchingConsole> (enable) set system name bg-sw-01/device nameBg-sw-01> (enable) set passwordEnter old password:Enter new password: test/device passwordRetype new password: testBg-sw-01> (enable) set enablepassEnter old password:Enter new password: test/device passwordRetype new password: testBg-sw-01> (enable) s
In the wireless network composition, the use of a lot of equipment is worth a detailed understanding. So today we're going to talk about the problem of VLAN wireless internet switch failures. The following is a netizen's experience sharing: Unit one office area where the two departments VLAN appeared a very strange problem, some websites on the internet can be normal access, and some sites are inaccessible; it's normal to receive mail via Outlook or Foxmail, and sending small messages without at
rules. Therefore, layer fourth switching technology is the ideal mechanism for data transmission and load balancing among multiple servers.
At present, there are many products to support multi-layer exchange, such as Cisco Catalyst 5509/6509, Extreme Diamond Series, Foundry Bigiron series and Alteon ace-180e and so on.
Multilayer switching technology has now been described as an integrated, complete solu
switches provide high-performance, multi-layer switching solutions for the campus network. They are designed specifically for application environments that require Gigabit scalability, high availability, and multi-layer switching, it is mainly intended for backbone connections in the park.
The Catalyst 6000 series is composed of Cisco switches of the Catalyst 6000 and
set of physical network devices, and use VLAN division of different virtual network segments to isolate the corresponding network and complete different functions. For details, see Figure 4.
The LAN is designed with a star structure. The Catalyst 6509 is designed for master-slave distribution that requires Gigabit expansion, high applicability, and multi-layer switching, and the application environment of
catalyst Switch ports or between the catalyst Switch and the router. Trunk links can carry multiple VLANs.Configure trunk links on IOS-based switchesSwitch (config) # interface mod/portSwitch (config-if) # switchport mode trunk // you can specify trunk as the port mode.Switch (config-if) # switchport trunk encapsulation {isl dotlq} // set the frame encapsulated by trunkSwitch (config-if) # switchport trunk
, can be selected according to the requirements, in this article will not be discussed.
First, dual export solutions
On the basis of the original Cernet access link, our school has opened a second export through telecommunications. And the increase of campus network export lines, theoretically improve the network bandwidth, but if not adjust the original network system structure, its effect can not be reflected. For this program, we have the following requirements:
(1) Client IP address setti
services have great advantages in network segmentation, security, manageability, and broadcast suppression. The purpose of the layer-3 switch is to replace the existing router. It provides information flow communication between subnets, so that the communication speed increases from several hundred packets per second to several million packets per second. Layer-3 switching is designed to forward multiple protocols at high speed, provide firewalls to protect network resources, or reserve bandwid
H3C routers have developed rapidly and are also very competitive in the market. Here we will introduce the performance of H3C router products in the market for your reference. Recently, the US-renowned media Network World has published its evaluation results on H3C router S7506E (3Com 7906E) to the outside World, h3C router S7506E scored a high score of 4.28 (out of 5) in the evaluation.
This evaluation lasted for five months and involved H3C routers S7506E, Cisco
(config-r-mc) # Return end to global ModeStep 5 Router # copy running-config startup-config save ConfigurationNote that the auto-sync standard command does not synchronize boot variables.The configuration is as follows:Router (config) # redundancyRouter (config-r) # main-cpuRouter (config-r-mc) # auto-sync standardRouter (config-r-mc) # auto-sync bootvarRouter (config-r-mc) # endRouter # copy running-config startup-configNote that manual synchronization of a parameter causes the original defaul
The naming rules for Cisco switches are more complex than the naming rules for routing,Look at these:ws-c2960-24tc-l, WS-C2950G-24-EI-DC, Ws-c2960-24tt-l, Ws-c3750g-24ts-e, Ws-c3750g-24t-s, We didn't find them on the switch, we just saw the Catalyst 2950 series and wrote it all: The Cisco Catalyst 2950 Series, which means the Cisco switch 2950 series, Catalyst Th
A strange problem occurs in the VLAN of the two Departments in the office area of the organization. Some websites on the Internet can access normally, but some websites cannot access it. emails received through Outlook or Foxmail are normal, it is also normal to send small emails without attachments, but it cannot be normally sent when sending large emails or emails containing attachments. Internet access is normal in other office areas of the Organization. The topology 1 of this part of the net
Many enterprises now have their own Metro Ethernet services. Here we will give you an analysis of the coexistence of Metro Ethernet and traditional WAN services, South Korea's Enterprise Networks Company (formerly GNG Networks) an Optical Transport MAN (MAN) is being built along the subway lines in six major South Korean cities (including Seoul) and plans to provide Metro Ethernet services for enterprises. Enterprise Networks uses the Cisco 15454 Optical Transport Platform.
It is equipped with a
the following:
Only the Fast Ethernet hybrid network module can support these two wan interface cards.
The network modules supporting these two interface cards are as follows:
NM-1FE2W, NM-2FE2W, NM-1FE1R2W, NM-2W.
The Ethernet hybrid network module does not support the following features:
NM-1E2W, NM-2E2W, NM1E1R2W.
19. What is the maximum rate of synchronization supported by Cisco3600 series routers (4A/S, NM (8A/S network module and WIC (2A/s wan Interface Card?
These network modules and WAN
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.