catalyst gigabit switch

the distribution layer or core layer that aggregates hundreds of Mbit/s/Gigabit Ethernet traffic, the IDS working on layer-3 software cannot process massive data. Therefore, it is impractical to monitor all traffic without any choice. How can we find a targeted, effective, and economically scalable solution? With the security features and Netflow integrated by the Catalyst

At present, the market support Gigabit Ethernet Technology Gigabit Switch products are numerous, manufacturers are also more, how to choose the right equipment in these varieties of equipment, is a need to carefully consider, time-consuming to understand and difficult to weigh the choice of the problem. Therefore, generally in our evaluation of equipment selecti

in the Catalyst switch, but is not valid for multicast traffic. 3550-1 # conf t 3550-1 (config) # mac-address-table static 00-90-F5-10-79-C1 vlan 2 drop/drops traffic on the corresponding Vlan. 3550-1 # conf t 3550-1 (config) # mac-address-table static 00-90-F5-10-79-C1 vlan 2 int f0/1/discard traffic on the corresponding interface. As network security becomes more and more important today

Catalyst 4000 and Catalyst 5000 of the Catalyst Switch series (Catalyst 6000, running CatcOs) support some form of authentication, starting with code 2.2. Added the latest version. TACACS + (TCP port 49, not xtacacs udp port 49), remote access dial-in user service (RADIUS),

Describes the overview and configuration methods of the Catalyst 1900 switch, the introduction of the Catalyst 1900 switch and the configuration of the Catalyst 1900 switch. The following describes the configuration of the

Catalyst Switch Security ConfigurationThe security configuration of the Catalyst switch is to prevent potential network security risks. We recommend that you take the following measures on each cisco device: 1. use enable secret to configure a strong password. Select a password that includes letters, numbers, and speci

Found that Cisco Catalyst Switch reboot is always in rommom mode, the system reboots when the Confreg command chooses the startup mode of 1 (starting from the first file) and cannot enter the normal interface. Enter to boot: 0 = Disable Autoboot 1 = the internal flash device 2 = commands specified in ' BOOT ' environment variable [2]: 1 The analysis suggested that the iOS file might be corrupted or pu

1. Unplug the power cord of the vswitch, press the switch Mode button, and re-plug the power cord of the vswitch. Release the Mode button after the LEDs on Port 1x are off. 2. For the Catalyst 2940/2950 L series: Unplug the power cord of the switch, hold down the Mode button of the switch, and re-plug the power cord of

The article I want to share and configure VLAN on Linux through Cisco Catalyst Switch.Requirements:1. Linux installed on a PC with one or more NICs (Network Interface Card). I Use the Centos 5.4 using 2.6.18-164.11.1.EL5PAE kernel. It should is applicable on other Linux distros such as Slackware, Ubuntu, Fedora, Debian, etc.2. Cisco Catalyst Switch 29503.2 Pc/lap

The backboard bandwidth in a Gigabit Switch mainly refers to the maximum data volume between the processor and the data bus. It should be said that it represents the comprehensive performance of the Gigabit Switch, which is one of the parameters we must carefully look at when purchasing. At present,

The gigabit router switch technology must meet several requirements without blocking. The gigabit router switch technology provides a detailed description of the requirements for non-blocking. This is a common problem. But how can we learn the Gigabit route

If the switch login password is forgotten, don't worry, as long as you have a PC, there are similar HyperTerminal (Hyper Terminal) This is a terminal program, connected to the switch console port, then the password recovery is n simple. 1. For the Catalyst 2900/3500XL series: Disconnect the power cable from the switch