Copyright Notice Update:2017-05-20Bo Master: LuckyalanContact: [Email protected]Statement: Draft not forget to dig well man, reproduced please indicate the source!1 Article IntroductionThis article describes the route command under Linux.2. Development platformLinux Systems3. Reading instructionsNo4 Article bodyThe route command for the Linux system is used to display and manipulate the IP routing table. To
The route command displays or modifies the route table of the local IP address. Syntax: [plain] route [-CFvnee] route [-v] [-Afamily] add [-net |-host] target [netmaskNm] [gwGw] [metricN] [mssM] [windowW] [irttI]... the route command displays or modifies the
The route command in Linux is used to display and operate the IP route table (show/manipulatetheIProutingtable ). To achieve communication between two different subnets, you need a router that connects two networks or a gateway that is located in both networks.
In Linux, routing is usually set to solve the following problems: the Linux system has a gateway in a LAN that allows machines to access the Interne
Tags: solve sbin production AST Equipment Gen Dash CTO answerLinux route command in layman's and actual case explaininghttp://blog.51cto.com/oldboy/1119453-route command in layman's use guidehttp://blog.51cto.com/oldboy/974194Video commentary of this blog post published: http://oldboy.blog.51cto.com/2561410/1119453Origin: This article for the old boy Linux training seventh pre-class exam questions and refer
The client needs to route some network segments to specific routes and use route to add rules. [Root @ localhost ~] # Route add-net 192.168.192.0/24 gw 192.168.191.1 note: the IP address of the gw gateway to be added to route add-net is invalid after each restart of the server.Solution:Add the statement to the/etc/rc.
Linux route, linuxroute
I. Introduction
The route command in Linux is used to display and operate the IP route table (show/manipulate the IP routing table ). To achieve communication between two different subnets, you need a router that connects two networks or a gateway that is located in both networks. In Linux, routing is usually set to solve the following pr
Static RoutingSet 5 U + G7 w6], W + W * m
With the popularization of broadband access, many families and
SmallEnterprises have established local networks to share broadband access. In addition, with the expansion of the LAN, the applications of two or more routers are involved in many areas. When there are more than two routers in a LAN, you often need to set up routes because of the mutual access between hosts. Large network scale
SmallAnd does not change frequently, so
Static RoutingIs the mos
"Theoretical Preparation"
The way the OSPF default route is published depends on the type of zone that introduces the default route, mainly for common areas, stub regions and complete stub regions, Nssa regions, and fully nssa areas.
OSPF default route Publishing method:
L Configure a specific area for automatic generation, stub/totally stub/totally Nssa
L Co
1. Specific functionsThis command is used to display and modify entries in the local IP address routing table. Use a route without parameters to display help.
2. Syntax explanationRoute [-F] [-p] [Command [destination] [mask netmask] [gateway] [metric] [If inte *** ce]3. parameter description-FClear all routes that are not the primary route (the subnet mask is 255.255.255.255), the back-to-network
In the previous article, we used the description of the SIP Routing Mechanism to understand the definition and concept of the SIP routing mechanism. Next, let's explain these abstract concepts to help you understand them. Next, we will use two SIP routing instances to help you understand these concepts.
SIP route Example 1:
Scenario: There are two proxies between two UE, U1-> P1-> P2-> U2, and both proxies are willing to add Record-
Many students have been at home to build a wireless network, but because of barriers such as wall block, so that wireless signal attenuation is very severe, in order to solve this problem many students have begun to try to use Wireless bridge router in the home to expand the range of wireless network
But many students reflect that the router bridge is successful, but still can only from the main route (a route
The route command is used to display and modify entries in the local IP address routing table. Use a ROUTE without parameters to display help.
Syntax:
Route [-f] [-p] [command [destination] [mask netmask] [gateway] [metric] [if interface]
Parameter description:
-F
Clear all routes that are not the master route (the sub
The original address; http://www.cnblogs.com/peida/archive/2013/03/05/2943698.htmlThe route command for the Linux system is used to display and manipulate the IP routing table (show/manipulate the IP routing table). To achieve communication between two different subnets, you need a router that is connected to two networks, or a gateway to two networks. In Linux systems, routing is usually done to address the problem that the Linux system has a gateway
The fact that r I p records only one route for each destination requires r I P to actively maintain the integrity of the route table. This is done by requiring all active r I p routers to broadcast the contents of their route tables to adjacent r I P routers at regular intervals, all received updates automatically replace the information already stored in the
XP multi-Nic static route setting methodOne, multiple IPs are in the same network segment or VALN. There's nothing to say about this, but you can set the IP address, subnet mask, and default gateway in the local connection properties of each NIC.Two, multiple IPs belong to different network segment or VLAN. At this point, if you set the IP address in the usual way, fill in the subnet mask and default gateway of each network segment, you will find that
Tags: blog HTTP ar use SP data 2014 on Log
Different kernel protocols do not directly use the functions provided earlier to access the routing tree. Instead, they call several functions: rtalloc and rtallocl, which are used to query route tables.
The rtrequest function is used to add or delete route table entries. In addition, most interfaces call the rtinit function when the interface is connected or disco
Introduced
The route command in the Linux system can be used for the display and operation of IP routing tables. Its primary role is to create a static route that specifies a host or network through a network interface, such as eth0. When you use the "add" or "del" parameters, the routing table is modified, and if there are no parameters, the current contents of the routing table are displayed. In a networ
View Linux kernel route table
Use the following route command to view the Linux kernel route table.
# routeDestination Gateway Genmask Flags Metric Ref Use Iface192.168.0.0 * 255.255.255.0 U 0 0 0 eth0169.254.0.0 * 255.255.0.0 U 0 0 0 eth0default 192.168.0.
The route command for the Linux system is used to display and manipulate the IP routing table (show/manipulate the IP routing table). To achieve communication between two different subnets, you need a router that is connected to two networks, or a gateway to two networks.In Linux systems, routing is usually done to address the problem that the Linux system has a gateway in a local area network that allows the machine to access the Internet, so the IP
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.