cisco 1841 router

Cisco router Startup ProcessThe Startup Process of a Cisco router is divided into four main stages: 1. execute POST 2. load the bootstrap program 3. search for and load Cisco IOS software 4. find and load the startup configuration file, or enter the setup Mode 1. executing P

Before giving you a detailed introduction to the Cisco router ACL, first let everyone know about the ACL, and then give a full introduction to the mask to block the scam attack. Wildcard-mask wildcard mask in the Cisco router ACL Access Control List ). Brief: The wildcard mask (or anti-mask) used in the

Assume that two Cisco routers and R1 (server) connect to R2 (client) to form a simple chained lan. DHCP is implemented below. The configuration commands and explanations are as follows: 1. Configure the R1 dhcp Service Dhcp # configure terminal // Enter global Mode Dhcp (config) # service dhcp // Enable the dhcp Function Dhcp (config) # no ip dhcp conflictlogging // Disable dhcp logging Dhcp (config) # ip dhcp pool

Use the home ADSL line and use the CISCO router to build the PPPoe Server so that the PC can access www.2cto.com R1 (config-if) # do sh runBuilding configuration... Current configuration: 1470 bytes! Version 12.4 service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption! Hostname R1! Boot-start-markerboot-end-marker !! No aaa new-modelmemory-size iomem 5 !! Ip

You can configure a serial interface through a virtual terminal. to configure a serial interface, follow these steps: 1. In Global mode, enter the command "interface serial 0" to enter the serial interface configuration mode. 2. Each connected serial interface must have an IP address and subnet mask to forward IP packets, in interface configuration mode, enter the "ip address 3. If the serial interface is connected to a DCE device, we also need to configure a clock frequency for the serial inte

First, give an environment:Cisco router Intranet interface s1/0: 192.168.1.1 255.255.255.0Internet interface s1/1: 10.0.0.1 255.255.255.0Server ip Address: 192.168.1.100First telnet to the vrotelnet:User Access Verification Username: cisco # enter the user namePassword: # enter the PasswordRouter> en # Enter privileged ModePassword: # enter the privileged mode PasswordRouter # conf t # enter global configur

Analysis of Cisco router IOS backup and recovery Introduction: I. Wiring Serial Interface-> console and pc Nic interfaces-> F0/0 // The IP address of the PC and the F0/0 interface (of course, other interfaces can be connected to the network cable). The IP address can be in the same network segment. You can also use an Internet ip address! Ii. Tools 3 CDaemon (tftp server) and CRT (access routing tool) Iii.

Here we will mainly introduce the configuration and initial installation of Cisco routers. Describes how to configure Cisco router settings and remote access, this article discusses how to use the DHCP service function of the internal network to allocate address information for users who remotely dial in and how to troubleshoot common vro faults. 1. Initial insta

When the iOS corruption in router needs to be restored, Ctrl+break (Packettrace is CTRL + C) When the router starts, enters Rommon mode, and the command prompt changes to: Rommon 1>Then enter the following command:Rommon 1>IP_ADDRESS=A.B.C.D//router's current IP addressRommon Subnet mask for 2>ip_subnet_mask:x.x.x.x//routerRommon 3>default_gateway=y.y.y.y//Router

Release date:Updated on: Affected Systems:Cisco ASR 9006Cisco ASR 9006Description:--------------------------------------------------------------------------------Bugtraq id: 48811Cve id: CVE-2011-2549 Cisco ASR 9000 series is an integrated service router solution that uses the Cisco ios xr Software module operating system to provide carrier-level reliability.

In this experiment, the speed limiting device of a Cisco router is completed by a Cisco2811 router. In this experiment, we will first look at the flash: www.2cto.com yourname # dirDirectory of flash on the router in two ways: /1-rw-25438028 Oct 22 2010 02:25:58 + 02:26:08 c2800nm-ipbase-mz.124-15.T.bin2-rw-1505280 Oct

, dynamic address translation, and multiplexing dynamic address translation. The following example uses a Cisco router.1. Static address translationStatic address translation performs one-to-one conversion between the internal local address and the internal legal address, and specifies the legal address to which the conversion is required. If there are WWW servers or FTP servers in the internal network that

1. Use the ip verfy unicast reverse-path network interface command This function checks each packet passing through the router. In the CEF (Cisco Express Forwarding) Table of the router, the router discards the packet if it does not have a route from the source IP address of the packet. For example, if the

Vro is a commonly used network device. I believe everyone knows the importance of backing up the cisco router configuration file. Next we will introduce how to use the COPY command to back up the cisco router configuration file, and how to COPY and back up the cisco

1. TELNET Remote logon Configuration 1. Configure the Logon account, password, and account level on the CISCO router, as shown below. The account name is abc, the password is abc123, And the account level is 15 to the highest level) R1 # configure terminal R1 (config) # username abc privilege 15 secret abc123 R1 (config) # end R1 # 2. Configure the remote logon authentication mechanism for the

that needs to be mapped to the Internet for access by others. The specific requirements are as follows:1. Only Internet users are allowed to ping the server and log on to the server through SSH;2. Only Intranet users are allowed to ping the server and log on to the server through telnet;3. Intranet users can access the Internet freely;4. The server cannot access the Internet.Step 1:First First, ensure that the server and PC can ping the gateway GW, then perform NAT on the GW, and ensure that t

When configuring the Cisco 3560 switch in the morning with the Cisco Packet Tracer practice, it is found that the IP address of the port cannot be configured in port configuration mode.Switch>Switch>enableSwitch#configure TerminalSwitch (config) #interface F0/1Switch (config-if) #?DhcpOnly DHCP commands are available. Check on the Internet, the original switch port is Switchport, that is, the two-layer swit

1. Preface A large number of Cisco routers are used in Jiangxi IP networks. Administrators usually use Telnet to remotely log on to the vro for routine maintenance. Because Telnet, FTP, and other network service programs use plain text transmission passwords and data in the network, their security cannot be effectively guaranteed. Once the Administrator's user name and password are intercepted by someone with ulterior motives, the consequences will b

The VPN configuration of the Cisco router is not important for network security, but also makes the user more convenient during use. In this experiment, we use the Cisco 2600 router and the Cisco router VPN configuration to implem

Cisco router startup process:(1) execute Bootstrap Loader in the ROM, which is similar to the BIOS in the computer and Bootstrap will install IOS into RAM;(2) IOS can be stored in many places (FLASH, TFTP server or ROM). The order in which the router looks for IOS images depends on the startup domain of the configuration register and other settings. Configuration