Analysis of Cisco Broadband Access configuration method
China Telecom's bandwidth is 2 M and the assigned fixed IP Address: 202.249.11.101 subnet mask: 255.255.255.255.248 Gateway: 202.249.11.20Planned LAN address range: 192.168.0.2-192.168.0.254 subnet mask: 255.255.255.248 Gateway: 192.168.0.1The vro provides a 1721 M Adaptive port for Cisco 10/100. Next, we need to configure a 1ENET expansion card with
In fact, many brands of vro configuration commands are very similar. Therefore, this article provides a comprehensive analysis of commonly used Cisco vro configuration commands for Cisco vrouters, at the same time, I learned more.
The basic status of a vswitch with the Cisco router configuration command:
Switch:; ROM s
Global debugging
When configuring a Cisco router, the boundaries between global and interface commands are obvious. In this case, we use "Global" to identify commands that cannot be used for interface debugging or specific transmission media types and Protocol debugging. For example, in vrouters 2500, you can use Debugging commands to analyze the Cisco Discovery
Some of the comrades may not be very clear about the DHCP configuration of Cisco routers, and most people do not know about the computer, so, the customer asked us to allow any computer to access the LAN to access the Internet, so we had to configure DHCP 2600. 2600 router we identify as: Cisco enters global mode.
Cisco
It is useful to know about Cisco router configuration. Here we mainly explain the specific steps of Cisco router configuration. Cisco routers once dominated enterprise wide area network applications. However, according to the CCID report in recent years, huawei and
Topology map:
1. Configure the router R4 as a Frame relay switch
Frame-relay switching * configured as Frame Relay switch
2. Configure the interface's clock frequency, package type, LMI type and Frame Relay DCE on the router R4
int s0/0
No shut
Clock rate 64000 * Set clock frequency
Encapsulation Frame-relay * Encapsulated as Frame Relay
Frame-relay lmi-type
Network is inseparable from the password, as a network administrator to remember more than one router password, if the router password forgotten, we need to set up a router to restore the password.
Router password recovery has a common, that is, let the router start to skip
Cisco router Entry 1First, let's take a look at the Memory RAM of one of the vro's internal components: Random Access to the memory, which is equivalent to the memory of the computer and is volatile (all storage content will be lost after power failure ), the main software running is the IOS image and configuration file. ROM: read-only memory, which resident some microcodes used to start and maintain basic
Network security management involves many aspects. However, looking at many security events, we can draw a basic conclusion that the harm is caused by ignoring basic security measures. This article will discuss the importance of maintaining Cisco Router password security, explain the three modes of Cisco router IOS, an
In network management, we usually handle the problem about Cisco router DHCP. Our netizens also participated in some of the discussions. Here we will summarize them for your reference. There may be no specific mode to describe Cisco router DHCP problems, so the following questions and replies from netizens may not help
It is very important to know more about the configuration of Cisco routers. Here we mainly analyze the configuration steps of Cisco routers, have you ever encountered this problem: Because you forgot your password, you were forced to reject the original friendly "friend"-A vro or vswitch, and you were unable to reset parameters and collect statistics. The following describes how to clear passwords for sever
By David Davis CCIE, MCSE + I, scsa | more from David Davis CCIE, MCSE + I, scsa | published: 5/26/05Category: Home | audience: Networking Communications
Takeaway:It's critical that all devices on an organization's network display the accurate time and date. if they don't, things can go wrong in a hurry. david Davis explains why Cisco devices need to use Network Time Protocol (NTP) for their time synchronization needs, and he tells you how to configu
CISCO PT Simulation Experiment (11) router single-arm routing configurationExperimental Purpose : Master The configuration method of single-arm routingImplementing different VLANs to communicate with each otherIn-depth understanding of VLAN communication Principles and routing sub-interfacesExperimental Background :the company's technical and sales departments in different offices, technical department and
I. i0s process
The i0s process is a special software task that runs on a router and is used primarily to implement a function. When we configure i0s with the command-release profile, it is actually the same as controlling the behavior that makes up the 10S processes, all of which run concurrently on the router. The number and type of processes that can be run on one ro
1. Use the Cisco router Debug cable to connect the router's console interface and the computer's serial port, turn on the router after powering on, and then 1. In Windows XP, initial debugging via the HyperTerminal logon router, as shown in network topology 7-8650) this.width=650; "title=" QQ picture 20150320165214.png
This article describes in detail how to set the default settings for Cisco routers in terms of security analysis, specific measures, and default settings. I believe this article will help you.
Security Analysis
Readers who have experience configuring routers should know that network administrators often set access control lists on routers or switches to prevent viruses and hackers. By default, the "deny any" statement is added to the access control li
The company's GPS patrol system needs to go WVPDN to communicate, but before looking for a telecommunications took a CISCO2811, collapsed once, the 2811 is the telecommunications sent, the estimated quality is not how, and then to find the company to buy the same type of equipment, 2811 discontinued, on the Cisco 2911.Yesterday arrived Ah, excited a bit, super terminal connected on, looked at the system configuration, the result of the hand is cheap,
When a Cisco router forgets or loses the enable password, there are two methods to restore it, depending on the series of products you are using.
Method 1
You can use this method to restore the following vrouters: cisco 2000 Series, 2500 series, 3000 series, Cisco 680 series with 4000x0 Motorola CPU, and 10.0 series r
Article Title: simulate a cisco router using dynamic in Linux. Linux is a technology channel of the IT lab in China. Includes basic categories such as desktop applications, Linux system management, kernel research, embedded systems, and open source.
Environment: centos5.2
Software: dynamic. cisco-ios
1: Download the dynamic binfile.
Wget http://www.ipflow.utc.fr/
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.