I. Overview:
In the actual work can often see a strong SSL VPN can bypass deployment, and support routing mode and NAT mode: Router mode requires intranet to VPN assigned address pool address can be router; NAT mode, VPN Client access intranet host, intranet host sees address as VPN interface address, Therefore, the address intranet of the VPN address pool is not required to be routed. If you want to test
Test environment:
Cisco Router Intranet interface F0/1:192.168.1.1 255.255.255.0
External network Interface f0/0:10.0.0.1 255.255.255.0
Server ip:192.168.1.100
First configure on the router:
Router>en #进入特权模式
router#conf T #进入全局配置模式
Enter configuration commands, one
255.255.255.0 IP nat outside no IP mroute-cache Bandwidth 2000 No Fair-queue clockrate 2000000 Interface Serial1 No IP address shutdown No IP classless IP route 0.0.0.0 0.0.0.0 Serial0 access-list 1 Permit 10.1.1.0 0.0.0.255 Line con 0 line aux 0 Line vty 0 4 password Cisco End 3, multiplex dynamic address conversion applicable environment: Dynamic Address Translation is a dynamic address conversion, but it can all
Cisco routers are widely used in network interconnection. Among them, 2500 series routers are widely used in low-end users. So what if you accidentally forget the superuser password of the 2500 series router? Don't be afraid, as long as you can restore as follows:Preparation: a computer running Terminal simulation program can start a Super Terminal in Windows 95/98), and the microcomputer serial port COM1/C
The Cisco router NAC solves the problem. The so-called NAC is an architecture that allows multiple hardware and software components to work together to protect the user's network from adverse client attacks. 1. It is not easy to fully implement NAC, because the entire architecture contains too many different components from other vendors. For example, the architecture contains the NAC Policy Manager and mul
:(1) Step 1: Configure the Router Ethernet interface IP address(2) Step 2: Configure the router password(3) Step 3: Access the router via TelnetCommands for the relevant steps:Configure the Router Ethernet interface IP address (enter the privileged mode, global mode, interface mode, and configure the Ip-> activation in
Cisco router Tcl script backdoor 2nd tests
Author: Vic
The security of Cisco routers is certain. Password verification is required for remote login. The Cisco passwords are encrypted in the following ways:1 not encrypted, plaintext display
650) this. width = 650; "border =" 0 "alt =" "src =" http://img1.51cto.com/attac
-Negotiate with(can be automatically negotiated or manually configured, the routing protocol cannot be transferred at both ends in the case of Autonegotiation)4 , client (config-if) #ipmtu 1492-------------------- mtu value because pppoe data in encapsulation, A pppoe 8 5 , Client (config-if) #encapsulationppp------------- encapsulated into PPP6 , Client (config-if) #dialer pool7 , Client (config-if) #pppauthentication chap callin8 , Client (config-if) #pppchap hostname admin19 , C
method One: Router1#reload in 20Reload scheduled for 11:33:53 EST Sat Feb 1 2003 (in minutes) Proceed with reload? [Confirm] method Two:router1#reload at the 2Reload scheduled for 14:00:00 EST Sun Feb 2 2003 (in hours and minutes) Proceed with reload? [Confirm] Configuring Cisco router-specific time restarts
. RPF reverse transmission path forwarding) is an input function activated on a network interface or sub-interface to process packets received by the router.
It is very important to enable the CEF function on the vro, because RPF must rely on CEF. Unicast RPF is included in Cisco IOS 12.0 and later versions that support CEF, but does not support Cisco IOS 11.2 or
Experiment Name: Cisco router network address translation (NAT)Experimental purpose: To achieve all intranet IP to use a small number of public IP network connection to the InternetExperiment Introduction:With the help of NAT technology, when the intranet private address sends packets to the router, the private address is converted to a legitimate public IP addre
supports SSH. log on to your vro or vswitch and check whether you have loaded an IPSec IOS image that supports SSH.
In our example, we will use the Cisco IOS command. Run the following command:
Router> Show flash
This command displays the name of the loaded IOS image. You can use the result to compare the list of supported features of your supplier.
After you verify that your device supports SSH, make sure
1. Password Recovery Principle
1) The Cisco router stores several different configuration parameters and stores them in different memory modules. The memory of Cisco Series routers includes ROM, Flash memory, RAM, immutable RAM, and Dynamic memory DRAM. See table 1 ). Generally, when a vrodram starts, it first runs the program in ROM, conducts system self-check
The rapid development of wireless networks has also promoted the wide application of wireless routers. At present, the market demand is also very high. Here we recommend a Cisco wireless router, cisco's Linksys wireless products have always maintained Cisco's high quality. As a result, this WRT54GC Cisco Wireless Router
ExploitationScriptConfigureCisco router configurationBefore that, you must specify the operations you want to perform, execute those commands, and then write scripts. I want to back up the running-configure configuration. Of course, the device has been configured and the tftp server is ready. The Cisco router configuration is as follows:
BT Wireless Network crac
I want to introduce a Cisco router simulation program to you today. I hope that a friend who is looking for software can take a look at this article to avoid some unsuitable factors after you download it. Software type: domestic software, authorization method: Shared Software, interface language: Simplified Chinese, Software size: 32.5 MB, file type :. exe, running environment: Win2003, WinXP, Win2000, Win9
and a switch are connected with the console lineHow it works: Switch password recovery fundamentals: Change the Config.text file name in the switch to a different file name, and then enter the configuration mode to change the password, and finally restore the Config.text file nameSteps:1. Power off first2. Power off while holding down the mode key on the switch until the display light on the switch is no longer flashing (5~10s), then release3. At this point, enterSwitch:flash_init (Initialize F
Cisco router configuration manual Virtual LAN (VLAN) routing 1. The main network technology we currently use when constructing an enterprise network is generally based on exchange and virtual networks. The exchange technology changes shared media to exclusive media, greatly improving the network speed. The Virtual Network Technology breaks the restrictions of the geographical environment. without changing t
Cisco router has become a commonly used network device, but we are not very clear about its storage classification. Here we will introduce it in detail.
Memory category:
1: RAM: Random Access to memory, equivalent to computer memory
2: ROM: read-only memory. Some microcodes used to start and maintain the router are resident in the ROM.
3: FLASH Memory, equiva
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.