cisco 2950 switch configuration

password to enter the privileged mode, and the original configuration content is retained.Operation steps: 1. Prepare the console cable and connect the Super Terminal. 2. Restart the switch (because 2950 does not have a power switch, you can directly unplug the power cord and connect it back.) 3. Press the MODE key at

attaches the host port number to the group Destination Address GDA) list. Similarly, when the switch hears an IGMP exit request, it moves the host port number from the entry of the content addressing memory CAM table. By supporting hardware IGMP listening and implementing IGMP listening configuration through the Cisco cluster management suite, the Catalyst

#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--

an IGMP exit request, it moves the host port number from the entry of the content addressing memory CAM table. By supporting hardware IGMP listening and implementing IGMP listening configuration through the Cisco cluster management suite, the Catalyst 2950 vswitch provides excellent performance and ease of use when controlling and managing LAN multicast applicat

Cisco 2950 switch VLAN division first configure the switch SC-2950> SC-2950> enSC-2950 # conf tEnter configuration commands, one per line. e

Configuration example of cisco router and layer-3 Switch environment, cisco layer-3 SwitchSimple environment configuration instance for cisco router layer-3 Switch I. network topology:

(POTS), digital telephone and ISDN traffic on the same media, or with Asymmetric Digital user line (ADSL) in the same line bundle, therefore, service providers can configure LRE for buildings that already use broadband services. Product Overview The Cisco Catalyst 2950 LRE Ethernet switch is a fixed configuration and

An instance of VLAN configuration for Cisco L3 switches and L2 SwitchesCisco VLAN implementation is usually port-centric. The port connected to the node determines the VLAN in which it resides. There are two ways to allocate a port to a VLAN: Static and Dynamic. The process of creating a static VLAN is to forcibly allocate the port to a VLAN. That is, we first create a VLAN on The VTP (VLAN Trunking Protoco

Previous page Everyone talked about Cisco Basic Operation command switch, while dragon boat holiday, the Cisco simple switch configuration, and hope you share "Happy Dragon Boat Festival"! Ok, configure the switch, first, you must

CISCO router switch SNMPv2 configuration, cisco Router Cisco router SNMP Configuration Snmp-server community CQGASPZW-R RO // ro read-only Snmp-server trap-source Loopback0 // use the loopbackaddress as the source address of the

Technical standards for VLANs IEEE 802.1Q was formally promulgated by IEEE Commissioners in June 1999, and the earliest Vlna technology was proposed by Cisco (Cisco) companies in 1996. With the development of the past few years, VLAN technology has been widely used in large and small enterprise networks, becoming the most popular Ethernet LAN technology at present. This article is going to introduce one of

, adding switches and end devices1, double-click switch into switch command line (CLI) mode, switch configuration mode by command2 in most cases for security reasons, you need to configure the switch privileged mode passwordValidation test3 Configuring the telnet login switc

Password recovery for Cisco Catalyst 2950 Switches1. Unplug the power cord from the switch.2. Press and hold the switch's mode key to plug in the power cord.3. When "Switch:" appears, release mode switch:4. After the SWITCH: Execu

(global configuration mode)S1 (config) #interface vlan 1 --Enter VLAN 1 PortS1 (config-if) #ip address 192.168.1.1 255.255.255.0 --Configure the vlan1 with an IP address so PC1 and S1 can ping interoperabilityS1 (config-if) #no shutdown --activating VLAN 1 PortS1 (config-if) #end --Return to privileged modes1#copy running-config startup-config --Save configuration (from memory RAM to hard disk NVRAM)s1#sh

configuration, which has been written for a long time,2950 The basic configuration of the switch, currently we are commonly used to configure the VLAN, the other is easy to manage, configure the IP address and allow Telnet login. Like spanning tree and VTP, the general small enterprises or systems are not configured,

configuration information from NVRAM4000> (enable) Erase all delete content in Flash4000> (enable) Show Flash displays content in Flash4000> (enable) show CAM [count] dynamic|static|permanent|system [vlan_#] Show cam tableVLAN 1900 (config) # VTP domain vtp_domain_name defining the switch domain name1900 (config) # VTP server|client|transparent define switch VTP

-if) # channel-group 1 mode desirable Switch (config-if) # end Appendix: Switch (config-if) # channel-group port_channel_number mode {auto | desirable | on} // Add the physical port to an Ethernet channel and determine the PagP mode. 3) layer-2 Ethernet Channel Configuration Switch # configure termina

Cisco LAN switches are still commonly used. So I studied the maintenance and configuration problems of Cisco LAN switches. I would like to share them with you here, hoping to help you. Cisco LAN switches have evolved from a HUB-based LAN shared in the traditional sense to a broader space. Take Cisco's ipvst5000 series

Cisco Fabric Manager is a Web-based, easy-to-use, responsive application that can be used to manage switches and networks in an integrated manner, thus simplifying the storage lan san) management of Cisco MDS 9000 series switches. Cisco Fabric Manager provides network-level management functions for storage administrators, including identification, multi-

Cisco switch by default. But it can be implemented with only one command, namely: 3550 # terminal monitor. In order to experience the actual effect, we can open two DOS windows on our PC and log on to the same Cisco switch through TELNET. One is used for monitoring, and the other is used to perform specific operations