With the development of China's routing industry, we have also promoted the update and upgrade of the routing switch technology. Here we have introduced the IOS restoration method of the Cisco routing switch, and we have tried one method, after Flash is deleted, the system cannot be started. You can use X-Modem to restore it. At that time, I accidentally deleted
First of all, the Cisco, the orders are not many, are basic. Not including STP, upgrades, Acl,web and the like.Ruijie and Cisco 99% are similar.CISCO layer-2Switch>go to HyperTerminal console switch>Enable access switch privileged mode switch#configure terminal Enter
The detailed steps for restoring the password of a Cisco switch are illustrated. If the password of a Cisco switch is improperly restored, the password will be lost. Today, we will contact the steps for restoring the password of a Cisco
CISCO router device categoryThe name rules of cisco routers start with cisco, such as cisco2611 and cisco2610. cisco is the name of the device manufacturer, 26xx represents the 2600 series routers, and xx is a more detailed classification. The following lists several common series of
Experimental topology
Router (config) #frame-relay switching to simulate a router as a Frame relay switch
Router (config) #inter S1/1
Router (config-if) #clock rate 128000
Router (config-if) #encapsulation Frame-relay Configuration Interface encapsulation and binding relay
The default Frame relay enabled on the interface is encapsulated in the Cisco package and, if connected to a non-
High intelligence, high availability, and high reliability are the characteristics of multi-layer intelligent optical fiber switch. Although its technology is not very mature yet, it has been recognized by people. Cisco Systems recently announced that it will launch the CiscoMDS9100 series of multi-layer smart Optical Fiber switches this fall to meet the needs of small and medium-sized enterprises for deplo
The port rate between switches and switches, between switches and routers, does not meet the actual rate and requires tying more than two ports together to load balance and prevent single points of failure.1. Select Switch SW2960 to configure the F0/1 and F0/2 port modes to truck#conf Terminal into privileged mode#interface Range Fa0/1–2 used to bind a set of ports and enter the port batch configuration view Figure#switchport mode truck will figure p
In the middle of a Cisco switching network, how do I find out which port of the switch is connected to the IP address of a machine? The most convenient and quick way is to use the User tracking function of the CiscoWorks 2000 LMS network management software. The graphical interface is clear at a glance.
If you do not have this software, you can use the following manual analysis method to find the answer:
Ex
Cisco switch,
Cisco switchesSwitch> enable
Switch # con
Switch # conf
Switch # configure ter
Switch # configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Cisco switch password settings www.2cto.com 1. set console password> enable # configure trminal (confing) # line console 0 secure console port ① (config-line) # password (cisco) Secure password (config-line) # login logs must not be small. console Password settings complete exit 2: set the global password www.2cto.com enadle # configure terminal ② (config) # enab
#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--Cisco Internetwork Operating
): can only receive or send bpdus messages
learning (learning) : can receive or send BPDU Message, and form mac
forwarding (Forwarding) : can receive or send BPDU Message, and form mac Address table, send and receive data frames simultaneously
STP Convergence: All ports on the switch are converted to forwarding or blocking mode, which takes 50 seconds by default. The
Overview of LAN switches
LAN switches have evolved from a HUB-based LAN shared in the traditional sense to a broader space. Take Cisco's Catalyst 5000 Series LAN switch as an example. It includes an integrated switching hardware structure, 10-Mbps Ethernet that supports switching, and-Mbps Fast Ethernet, supports fast Ethernet, FDDI, exchange-type ring, and layer-3 switching processing. This type of switch
)
--------------------------------------------------------------------------------
Add Catalyst 5002 to the domain
You need to add Catalyst 5002 To The VTP management domain named cisco and set it to VTP client. It will receive VTP configurations and updates from the VTP server.
Note: by default, the Catalyst 5000 series switches are VTP servers.
Cat5002> (enable)
Cat5002> set vtp domain cisco mode client
T
1. Unplug the power cord of the vswitch, press the switch Mode button, and re-plug the power cord of the vswitch. Release the Mode button after the LEDs on Port 1x are off.
2. For the Catalyst 2940/2950 L series:
Unplug the power cord of the switch, hold down the Mode button of the switch, and re-plug the power cord of the sw
Tags: Cisco MDS zone san Configure a Cisco MDS Optical Fiber storage switch (MDS multilayer Director Switch multi-layer optical fiber array switch)General process: 1: Create a vsan, add the port to vsan2: create a zone, add the port to zone3: Create a zoneset, add the zon
Basic configuration and management of the Cisco PT Simulation Experiment (1) switchExperimental Purpose : Master the basic configuration and management of the switch, and understand the basic commands of the switch configuration. Experimental background : A company has a new batch of two-layer switch, before formally p
Recently, the OS of a vswitch is old, so I want to update it. I want to ask a user to update the OS. After updating the OS, the problem occurs, I have a password for the OS. Since the password is being used and it is difficult for them to ask for it, I am ready to clear the password. After finding the relevant article on www.cisco.com, cleared successfully. Write down the cleanup process.
Let's talk about the configuration environment first, the switch
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.