cisco 3550 24 port poe switch

#Specified portIP 3550 (config-if) # no shutdown #Save Configuration 3550 (config-if) # exit #Back to previous Layer 6. Configure port 3: connect to the network segment 192.168.3.0/24 under Port 3 Gateway: 192.168.3.1 subnet mask: 255.255.255.0 DHCP pool: 192.168.3.101-192.

#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--Cisco Internetwork Operating

to each VLAN, VLAN starts up */"t. E 9U B Kw86 ": 8 www.2cto.comStep 3: Set the port global parameter {tsf-cx kE w _ 0] T-% 0 Switch (Config) interface Range Fa 0/1-24 _ | dT % ZI1 Switch (Config-if-range) Switchport Mode Access /* Add Port 9-16 to VLAN 3 */fq tFe % t

Cisco 3550 switch stp learning notes STP (Spanning Tree Protocol) (IEEE 802.1D) Spanning Tree Protocol-review the working principles of SW: 1. the frame it forwards cannot be modified. create a MAC-PORT ing table based on source MAC learning. forward the frames in the target MAC ing table directly from the correspondin

For complete syntax and application information about this chapter, seeCatalyst 3550 Multilayer Switch Command ReferenceAnd Cisco IOS Interface Command Reference For Release 12.1. Understanding Interface Types This section describes different interface types and some reference content for configuring these interfaces in detail in other sections. Other section

There are many things worth learning about the 24-port switch. Here we will mainly introduce the detailed descriptions of the various parameters of the 24-port switch. In network equipment, the

(config) #no monitor session 1Switch (config) #endSwitch#wrSwitch#show MonitorNo SPAN configuration is present in the system.3. Other(1) Port image filtering, port mirroring can do filter.Monitor session session_number Filter VLAN Vlan-id [, |-]* * Specifies which VLANs belong to the traffic that the source port is entering, and can be emitted from the destinati

The most widely used switch for small and medium-sized enterprises is the 24-port Gigabit Switch. Therefore, when purchasing a switch, you must make full consideration. A clear purpose is to save costs for everyone. In network equipment, switches may be the most familiar dev

When selecting a 24-port Gigabit Switch, we need to consider the number of its Mbit/s and Gbit/s ports, and then we can know the bandwidth value of its backboard. In network equipment, switches may be the most familiar equipment for network administrators, especially access layer switches. However, when purchasing switches, many brands seem to have identical tech

As the core network switch of our company, the CISCO3550 has been running stably for many years, and its functions can also meet our needs. However, its port speed limit function is not as easy to implement as some other switches, fortunately, the implementation method has been found recently. After the configuration is complete, it is verified with the iperf software. The result shows that this method is e

Port speed limit must start QoS on the switch Switch (config) #mls QoS//Start QoS on the switch Here are the implementation steps. First, create an ACL Since this is a three-layer switch, although the port speed limit, but also to

Introduction As the core network switch of our company, the CISCO3550 has been running stably for many years, and its functions can also meet our needs. However, its port speed limit function is not as easy to implement as some other switches, fortunately, the implementation method has been found recently. After the configuration is complete, it is verified with the iperf software. The result shows that thi

operations on core commands, let's talk about port security operations: first, disable port 3. Use the switchport mode access command to configure the port as the access port for port security configuration. Run the switchport port