cisco 3550 24

Figure Cisco Catalyst 3550 series smart Ethernet switches are a new type of enterprise-class stackable multi-layer switch that provides high availability, high scalability, and high security, and improves the management capabilities of network operations. With a series of Fast Ethernet and Gigabit Ethernet configurations, the Catalyst 3550 series can serve

#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--Cisco Internetwork Operating System SoftwareIOS (tm) C2950 software (c2950-i6q4l2-m), Version 12.1 (9) EA1, RELEASE So

This article describes how to configure a vswitch for a CISCO 3550 router and how to configure access control for a MAC address. In network management, users often encounter this situation: some users violate management regulations and modify their own IP addresses without permission to access restricted resources. Such behavior not only undermines information security rules, but may also cause network comm

In Cisco 3550, dhcp configuration is often discussed on the network, but there are mostly errors and omissions. According to the configuration described on the internet, after "ip helper-address dhcp server ADDRESS, in the project, I found that the client could not obtain the IP address from the DHCP server. I recently configured 3550 as the DHCP server relay pro

Network Environment: A 3550EMI switch is divided into three VLANs. vlan2 is the network where the server is located and is named server. The IP address segment t-[/[Xm1S3 is 192.168.2.0, subnet mask: 255.255.255.0, Gateway: 192.168.2.1 the Domain Server is windows 2000 advanceserver and serves as a DNS server. The IP address is 192.168.2.10, vlan3 is the network where client 1 is located, the IP address segment is 192.168.3.0, The subnet mask is 255.255.255.0, And the Gateway: 192.168.3.1 is nam

Lab Environment:1. Configure two VLAN 10 and VLAN 20VLAN IP address settings: 192.168.10.1 255.255.255.0 (192.168.10.1 is a VLAN 10 gateway address)VLAN IP Address setting: 192.168.20.1 255.255.255.0 (192.168.20.1 is a VLAN 20 gateway address)2. (Windows Server R2 operating system) set up a DHCP server to create two scopes VLAN 10 and VLAN 20,Get the IP address dynamically using VLAN 10 and VLAN 20. The DHCP server NIC accesses the switch FA0/1 port.DHCP server network card settings:ip:192.168.1

Cisco 3550 switch stp learning notes STP (Spanning Tree Protocol) (IEEE 802.1D) Spanning Tree Protocol-review the working principles of SW: 1. the frame it forwards cannot be modified. create a MAC-PORT ing table based on source MAC learning. forward the frames in the target MAC ing table directly from the corresponding port. for frames without target MAC ing/Target wide (Group) broadcasting, SW learns diff

For complete syntax and application information about this chapter, seeCatalyst 3550 Multilayer Switch Command ReferenceAnd Cisco IOS Interface Command Reference For Release 12.1. Understanding Interface Types This section describes different interface types and some reference content for configuring these interfaces in detail in other sections. Other sections describe the configuration process of physi

GNS3. Eve-ng should also be used with VMware workstation.Eve-ng Installation Tutorial:Software needed: VMware, Eve-ng.ova, WINSCP, SECURECRT, IOU, browser.1: Import the Eve-ng.ova file into VMware. and modify some configuration: memory, CPU, network adapter to change to host-only mode. Network segment to set why you own the same network segment.2: The look after boot. Input Username:root,passwd:eveGet started with some configuration: Modify ROOT_PASSWDConfirm again:Modify hostname:This is follo