cisco 3550 router

This article describes how to configure a vswitch for a CISCO 3550 router and how to configure access control for a MAC address. In network management, users often encounter this situation: some users violate management regulations and modify their own IP addresses without permission to access restricted resources. Such behavior not only undermines information se

: Switch> Switch> enable Switch # conf t Switch (config) # host 3550 3550 (config )#No ip dolo #This statement may indicate that the statement fails, but does not affect the subsequent results. You can omit it. 3550 (config) # line con 0 3550 (config-line) # noexec-t 3550 (c

Figure Cisco Catalyst 3550 series smart Ethernet switches are a new type of enterprise-class stackable multi-layer switch that provides high availability, high scalability, and high security, and improves the management capabilities of network operations. With a series of Fast Ethernet and Gigabit Ethernet configurations, the Catalyst 3550 series can serve

For details about how to configure DHCP for a CISCO 3550 switch, refer to some configuration content in this article for comparison and learning. After "ip helper-address dhcp server ADDRESS" according to the configuration described on the Internet, the project finds that the client cannot obtain the ip address from the DHCP server, I recently configured 3550 as

Network Environment: A 3550EMI switch is divided into three VLANs. vlan2 is the network where the server is located and is named server. The IP address segment t-[/[Xm1S3 is 192.168.2.0, subnet mask: 255.255.255.0, Gateway: 192.168.2.1 the Domain Server is windows 2000 advanceserver and serves as a DNS server. The IP address is 192.168.2.10, vlan3 is the network where client 1 is located, the IP address segment is 192.168.3.0, The subnet mask is 255.255.255.0, And the Gateway: 192.168.3.1 is nam

#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--Cisco Internetwork Operating System SoftwareIOS (tm) C2950 software (c2950-i6q4l2-m), Version 12.1 (9) EA1, RELEASE So

In Cisco 3550, dhcp configuration is often discussed on the network, but there are mostly errors and omissions. According to the configuration described on the internet, after "ip helper-address dhcp server ADDRESS, in the project, I found that the client could not obtain the IP address from the DHCP server. I recently configured 3550 as the DHCP server relay pro

Lab Environment:1. Configure two VLAN 10 and VLAN 20VLAN IP address settings: 192.168.10.1 255.255.255.0 (192.168.10.1 is a VLAN 10 gateway address)VLAN IP Address setting: 192.168.20.1 255.255.255.0 (192.168.20.1 is a VLAN 20 gateway address)2. (Windows Server R2 operating system) set up a DHCP server to create two scopes VLAN 10 and VLAN 20,Get the IP address dynamically using VLAN 10 and VLAN 20. The DHCP server NIC accesses the switch FA0/1 port.DHCP server network card settings:ip:192.168.1

Cisco 3550 switch stp learning notes STP (Spanning Tree Protocol) (IEEE 802.1D) Spanning Tree Protocol-review the working principles of SW: 1. the frame it forwards cannot be modified. create a MAC-PORT ing table based on source MAC learning. forward the frames in the target MAC ing table directly from the corresponding port. for frames without target MAC ing/Target wide (Group) broadcasting, SW learns diff

For complete syntax and application information about this chapter, seeCatalyst 3550 Multilayer Switch Command ReferenceAnd Cisco IOS Interface Command Reference For Release 12.1. Understanding Interface Types This section describes different interface types and some reference content for configuring these interfaces in detail in other sections. Other sections describe the configuration process of physi

Cisco is now the world's largest manufacturer of switching routes! Many of our businesses, large and small, can use the network, and it is possible to switch routes to Cisco! When we install network equipment, we may ask the network engineer to help us install it! Access to the router has a lot of passwords! What if we forget these passwords? We may have to make

CISCO router switch SNMPv2 configuration, cisco Router Cisco router SNMP Configuration Snmp-server community CQGASPZW-R RO // ro read-only Snmp-server trap-source Loopback0 // use the loopbackaddress as the source address of the

After the popularization of broadband, Cisco wireless router settings are frequently faced. So today, I am going to introduce you to the configuration skills of Cisco Wireless routers. I hope this article will teach you more things and bring convenience to your life. After broadband popularization, many friends who have multiple computers or laptops want to insta

There are many things worth learning about in the configuration of a Cisco Wireless Router. Here we mainly introduce how to use a vro to set up a PC to share the Internet, including knowledge about DHCP, security, TCP/IP network protocols, and so on. As a product designed specifically for broadband Internet sharing, a Broadband Router has the advantages of simple

Basic configurations of Cisco routers and Cisco router configuration commands En -- enter the privileged mode config t -- enter the global configuration mode wr (OR) -- save the configuration (otherwise, the configuration fails before the power-off) 1. Set the password for entering the vro Console In global configuration mode, enter line console 0 --- enter the '

12000 the Cisco router series is very suitable for small and medium-sized enterprises. Here we mainly analyze the performance characteristics of the Cisco router series. In today's information age, enterprise mail has become an essential tool for business communication and communication. With the new routing technology

Configuration example of cisco router and layer-3 Switch environment, cisco layer-3 SwitchSimple environment configuration instance for cisco router layer-3 Switch I. network topology: Ii. configuration command: 1. vro Configuration: Interface FastEthernet0/0 Ip address 10

The Cisco router market is very good. Many people may not understand how the Cisco router solves the router IP configuration parameters. It does not matter. After reading this article, you will certainly have a lot of GAINS, I hope this article will teach you more things. Fo

It is very important to know some knowledge about backing up the cisco router configuration file to make our vro more secure. Here we will give you a detailed introduction to this issue in several steps. The COPY command is often used during vro configuration. Next we will introduce how to use the COPY command to back up the configuration file, and how to COPY and back up the

Introduction This document describes how to upgrade the Cisco IOS software image on the connected router platform. Upgrade instances of vrouters 2600 and 3600 are also applicable to the vro platforms listed below. The name of the Cisco IOS software file may vary depending on the Cisco IOS software version, function s