Cisco router has become a commonly used network device, but we are not very clear about its storage classification. Here we will introduce it in detail.
Memory category:
1: RAM: Random Access to memory, equivalent to computer memory
2: ROM: read-only memory. Some microcodes used to start and maintain the router are resident in the ROM.
3: FLASH Memory, equiva
: single two-way authentication: www.2cto.com 2.2, CHAP authentication: CHAP: Challenge Handshake Authentication Protocol, full name: challenge Handshake Authentication Protocol. CHAP verifies the identity of the authenticated end through a three-way handshake. It is completed when the initial link is established. To improve security, it is periodically verified after the link is established. CHAP is safer than PAP because CHAP does not send plain text online, but instead sends a random number s
This article uses VPN technology to achieve interconnection between two parts of the network, simulate ISP, close to practicality, the article mainly shows us the specific operation steps, mainly the input of basic commands.
In this experiment, we use the Cisco 2600 router and VPN technology to achieve the network interconnection between one branch and two parts. To stay close to practicality, we still use
The Cisco router sets IOS to upgrade each other. My company's network department has a Cisco router 2501, but IOS is bad. Here I call it cisocB, and another 2501 router IOS is good, we prefer ciscoA. Good IOS is no longer available on my PC, but it is transferred to the PC t
encapsulation method used by the serial port or ISDN InterfaceEncapsulation sap specifies that the Ethernet 802.2 format Cisco password used on the network segment is SAPEnd exit Configuration ModeErase deletes flash memory or configures CacheErase startup-config Delete content in NVRAMExec-Timeout: specifies the time that the exec command interpreter has waited before user input.Exit to exit all configuration modes or to close an active Terminal ses
...Writing monlib sectors........................................................................................................Monlib Write complete Format:all system sectors written. Ok...Format:operation completed successfully. Format of Flash:completeProgram load complete, entry point:0x8000f000, size:0xcb80(5) TFTP to see if iOS upload is complete.(6) Rommon 8 > Reset//Restart routerCisco
Cisco router IOS upload and download 1. Prepare a console line and a network cable. The connection cable is connected to the console port of the computer. The network cable is connected to the computer and the F0/0 port of the router. (Only F0/0 can be used. The router has no system, the IP address configured for the
To emulate the password of the reset router with the Cisco Packet Tracer Simulator, the packet tracer default router port is off and needs to be manually enabled 650) this.width=650; "Src=" http://s3.51cto.com/ Wyfs02/m01/5a/21/wkiol1t3xxiqjwmeaakcapd2ghs648.jpg "title=" 2.png "alt=" Wkiol1t3xxiqjwmeaakcapd2ghs648.jpg "/>1. Shut down the
Build PPPoeServer with the home ADSL line and use the CISCO router to enable the PC to access the Internet www.2cto. comR1 (config-if) # doshrunBuildingconfiguration... Currentconfiguration: 1470 bytes! Version12.4servicetimestampsdebugdatetimemsecservicetimestampslog
Use the home ADSL line and use the CISCO router to
This article describes in detail what a CAR is, how to configure a CAR, how to check whether a CAR works on the corresponding port, and so on. I believe this article will help you.
Many organizations have established internal networks because of their work needs. Large Enterprises and organizations may also have established wide area networks (WAN ). There are many types of applications on the network. To ensure the good operation of the main applications, traffic control must be performed on th
The Cisco router switch sets automatic backup for IOS files and restores the automatic backup and rollback of Cisco IOS configuration files. The archive configuration mode function of IOS is required. Generally, only IOS versions 12.3 (4) All commands for automatic backup of the Cisco IOS configuration file are as foll
Use a cisco router to simulate how to configure a frame relay switch (configure 3640 as a frame relay switch): 3640 (config) # frame-relay switching ---------------------- enable the frame relay switching function of the router 3640 (config) # int s0/0 ------------------------------------- enter the s0/0 interface 3640 (config-if) # no ip add --------------------
Simple Local authentication:(config) #username admin password Cisco // Establish user admin password for Cisco Local User (default permission level is 1)(config) #line vty 0 4 (config-line) #login local / /call on- premises authentication / / above method configuration, the default entry is User mode ">" After Telnet, An en password is required to enter the "#" password
Some time ago, someone familiar with me asked me how to set up a bridge on a Cisco router )? At that time, due to the relationship between work, I just briefly talked to him. Today, we set up a Cisco router as a complete configuration command for bridging. Through this instance, you can learn how to use a
address of the TFTP server be entered. After the Server IP address is correctly entered, the router also requires the network administrator to provide the configuration file name to be backed up. Generally, we recommend that you use a file name that is easily remembered by the Administrator. At this time, the router will prompt the Administrator to press YES to confirm the operation.
3. copy tftp running-c
This article introduces some examples of the cisco router show command. in the network, the network administrator should know the status of the router at any time, so as to promptly troubleshoot the fault.
The show command can be run in both user and privileged modes. "show ?" Command to provide a list of available show commands.
Show interfaces:Display the sta
Router upgrade
IOS
Summary
Step 1:
Note:Using a TFTP server software with cisco TFTPServer or 3 CDaemon), 3Cdaemon is faster when the transmitted files are too large. 1. first, place the IOS file in the specified directory and enable the TFTP server software. 2. use the USB to switch to the console line to connect the router to the PC and use the CRT login softwa
.650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/6C/00/wKiom1U9BK6CCeFMAAHG5ppb-7E739.jpg "style=" float: none; "title=" 7.jpg "alt=" Wkiom1u9bk6ccefmaahg5ppb-7e739.jpg "/>Second, the various Cisco routers into the ROM state of different methods, but generally by the following three ways to enter the ROM state, in the use of the process can be entered separately.1, if the break is not blocked, you can press the Ctrl+break key to interrupt t
add text to automatically configure:Login and passwordTransport input outputExec-timeoutLocal AAASSH timeout and ssh authentication-retries to minimum numberEnable only SSH and SCP for access and file transfer to/from the router
6. Protect Forwarding Plane
Enables Cisco Express Forwarding (CEF) or distributed CEF on the router, when availableAnti
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.