cisco 3550 router

First, the experimental topologySecond, the specific configurationRouter (config) #do sh runbuilding configuration ... Current configuration:604 bytes!version 12.4no service Timestamps log datetime MSECNO service timestamps debug datetime MSECNO Service Password-encryption!hostname router!ip dhcp excluded-address 192.168.1.1!IP DHCP Pool ABCNetwork 192.168.1.0 255.255.255.0Default-router 192.168.1.1Dns-serv

that needs to be mapped to the Internet for access by others. 650) this. width = 650; "border =" 0 "alt =" "src =" http://www.bkjia.com/uploads/allimg/131227/02223S615-0.jpg "/> The specific requirements are as follows:1. Only Internet users are allowed to ping the server and log on to the server through SSH;2. Only Intranet users are allowed to ping the server and log on to the server through telnet;3. Intranet users can access the Internet freely;4. The server cannot access the Internet.Step

Cisco router reset enable password tutorial, ciscoenable Steps: 1. Restart the vro and press ctrl + Breack when ROM Monitor mode appears on the vro to enter ROM mode, for example: 2. Modify the vro register value, change the original register value 0x2102 to 0x2124, and then run the reset command to restart the device, for example: 3. After the password is changed, the value of the drop register in

Assume that two Cisco routers and R1 (server) connect to R2 (client) to form a simple chained lan. DHCP is implemented below. The configuration commands and explanations are as follows: 1. Configure the R1 dhcp Service Dhcp # configure terminal // Enter global Mode Dhcp (config) # service dhcp // Enable the dhcp Function Dhcp (config) # no ip dhcp conflictlogging // Disable dhcp logging Dhcp (config) # ip dhcp pool

Use the home ADSL line and use the CISCO router to build the PPPoe Server so that the PC can access www.2cto.com R1 (config-if) # do sh runBuilding configuration... Current configuration: 1470 bytes! Version 12.4 service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption! Hostname R1! Boot-start-markerboot-end-marker !! No aaa new-modelmemory-size iomem 5 !! Ip

You can configure a serial interface through a virtual terminal. to configure a serial interface, follow these steps: 1. In Global mode, enter the command "interface serial 0" to enter the serial interface configuration mode. 2. Each connected serial interface must have an IP address and subnet mask to forward IP packets, in interface configuration mode, enter the "ip address 3. If the serial interface is connected to a DCE device, we also need to configure a clock frequency for the serial inte

First, give an environment:Cisco router Intranet interface s1/0: 192.168.1.1 255.255.255.0Internet interface s1/1: 10.0.0.1 255.255.255.0Server ip Address: 192.168.1.100First telnet to the vrotelnet:User Access Verification Username: cisco # enter the user namePassword: # enter the PasswordRouter> en # Enter privileged ModePassword: # enter the privileged mode PasswordRouter # conf t # enter global configur

When the iOS corruption in router needs to be restored, Ctrl+break (Packettrace is CTRL + C) When the router starts, enters Rommon mode, and the command prompt changes to: Rommon 1>Then enter the following command:Rommon 1>IP_ADDRESS=A.B.C.D//router's current IP addressRommon Subnet mask for 2>ip_subnet_mask:x.x.x.x//routerRommon 3>default_gateway=y.y.y.y//Router

customized within a Network as needed without application. In the network, computers communicate through internal IP addresses. When the internal computer needs to communicate with the external internet, the device with the NAT Function (such as a router) converts an internal IP address to a valid IP address (that is, the requested IP address) for communication. 　　 2. NAT application environment 　　　　 Scenario 1: an enterprise does not want external n

Update the public ip address of the Cisco router. First, confirm how your network is going. Here we will talk about the configuration based on our network: first, remove the default route no ip route 0.0.0.0 0.0.0.0 xxx. xxx. xxx. xxx adds the new default route www.2cto.com ip route 0.0.0.0 0.0.0.0 xxx. xxx. xxx. xxx then remove the ACL to overwrite the no ip nat inside source list 1 pool BJ. RK overload re

Cisco router nat translation 1. One-to-one correspondence between the internal address and the egress address disadvantages: When the egress address resources are scarce, only a small number of hosts can be connected to the internet. 2. The internal address shares the egress address. The router uses the egress address and port number, as well as the external host

There are too many Qos information on the Cisco Router Traffic Control instance, but many of them are not practical. I have talked about a lot of theories. The following are the configurations on the routers of a subsidiary for your reference. In fact, as long as you understand the meaning of NBAR, CBWFQ, and WRED, traffic control can be configured as needed. Www.2cto.com Description: A subsidiary uses a 2