customized within a Network as needed without application. In the network, computers communicate through internal IP addresses. When the internal computer needs to communicate with the external internet, the device with the NAT Function (such as a router) converts an internal IP address to a valid IP address (that is, the requested IP address) for communication.
2. NAT application environment
Scenario 1: an enterprise does not want external n
Update the public ip address of the Cisco router. First, confirm how your network is going. Here we will talk about the configuration based on our network: first, remove the default route no ip route 0.0.0.0 0.0.0.0 xxx. xxx. xxx. xxx adds the new default route www.2cto.com ip route 0.0.0.0 0.0.0.0 xxx. xxx. xxx. xxx then remove the ACL to overwrite the no ip nat inside source list 1 pool BJ. RK overload re
Cisco router nat translation 1. One-to-one correspondence between the internal address and the egress address disadvantages: When the egress address resources are scarce, only a small number of hosts can be connected to the internet. 2. The internal address shares the egress address. The router uses the egress address and port number, as well as the external host
There are too many Qos information on the Cisco Router Traffic Control instance, but many of them are not practical. I have talked about a lot of theories. The following are the configurations on the routers of a subsidiary for your reference. In fact, as long as you understand the meaning of NBAR, CBWFQ, and WRED, traffic control can be configured as needed. Www.2cto.com Description: A subsidiary uses a 2
When we use Telnet to log on to the device, the user name and password are transmitted in clear text, in order to ensure the security of the data, we recommend the use of SSH login device. The following is the configuration of the Cisco router SSH:1. Configuring hostname and Domain-nameR1 (config) #hostname R1R1 (config) #ip domain-name frame.com2. Generate the key, here is the 1024-bit key, the key length
The port Mapping method enables access to specific port services from the Internet to the local area network internal machines. For example, the machine you are using is in a LAN connected to the Internet, all the services you open on the machine (such as FTP), by default, the outside world can not access. This is because your IP is the LAN internal IP, and the outside can access only the server you are connected to the IP, because the entire LAN on the Internet only a real IP address, and this
Encapsulation Frame-relay boot Frame Relay Package
Encapsulation Novell-ether rules the Novell unique format used on the network segment
Encapsulation PPP set PPP to the encapsulation method used by the serial port or ISDN interface
Encapsulation SAP rules the Ethernet 802.2 format used on the network segment the Cisco password is SAP
End Exit Configuration mode
Erase Remove flash memory or configure cache
Erase Startup-config Delete the conte
It is very important for Cisco router users to learn about commands for password recovery of Cisco routers. For many beginners, the ROM Monitor of Cisco routers is often unfamiliar or even daunting for a simple reason, first, we do not often use this mode and are not familiar with its related operations; second, Operat
In the BGP Route Selection protocol, you can filter the BGP Route Selection and update. To do this, you need to use the prefix list. I. prefix list features: (1) it can be incrementally modified. We know that we cannot delete an entry in the general access control list, if you want to delete an entry in the list, you can only delete all the entries in the list. In the prefix list, you can delete or Add an entry separately. Www.2cto.com (2) and prefix list can be used in
As the core device of network communication, Cisco routers are widely used. The following is my experience in practice:
Control port interface practices and connections
Connect one end of the control cable RJ45 in the Cisco2500/1000 series router accessories to the Cisco CONSOLE port, and the Cisco7000/4000 series router
This article describes how to configure a vswitch for a CISCO 3550 router and how to configure access control for a MAC address.
In network management, users often encounter this situation: some users violate management regulations and modify their own IP addresses without permission to access restricted resources. Such behavior not only undermines information security rules, but may also cause network comm
This article describes in detail how to skillfully set the speed limit for commonly used Cisco routers, and provides detailed operation steps. I hope this article will help you.
The so-called speed limit is to set the ACL Access Control List on the router) to block the port used by the Service, so as to prevent the normal operation of the service. For the btsoftware, we can try to seal its port. In general,
Everyone knows that the Cisco router ACL plays an important role in the security policy of the Cisco router. Therefore, it is essential for everyone to master these knowledge points. In fact, this content is involved in many places. Access List) is an ordered statement set. It is a Sort table that allows or rejects pac
Hardware and Software Versions
This configuration is applicable to all Cisco IOS software versions.
DCE edge is connected by Wan DCE cable.
DTE edge is connected by Wan DTE cable.
For more information about the wan dce/DTE cable, see the serial cable documentation.Network Diagram
650) this. width = 650; "src =" 51cto.com/uploads/allianz 110909/1212454314-0.jpg "border =" 0 "/>
This article is based on the following Configuration:
In this configuratio
The computers in the 172.16.4.0/24 network segment are servers, and we protect these servers from the virus attacks from the 172.16.3.0 network segment via reverse ACL settings.Configuration instance: Prohibit virus from 172.16.3.0/24 this network segment to 172.16.4.0/24 this server network segment.Access-list Permit TCP 172.16.3.0 0.0.0.255 172.16.4.0 0.0.0.255 established Cisco Simulator defines ACL101, allowing all calculations from 172.16.3.0 net
The question about the Cisco router interface is described in the following four steps. Based on the demonstration in the image, I believe that we should be able to clearly understand the question about the interface. You can configure a serial interface through a virtual terminal. to configure a serial interface, follow these steps:
1. In Global mode, enter the command "interface serial 0" to enter the ser
When we want to perform permission rating management on a Cisco router or switch, it is often necessary to assign different levels of users a command that exceeds the default settings, such as show run, which is the most basic troubleshooting command.However, the command cannot be executed when your user level is at 0-14. You can assign permissions to these users using the following command:Privilege EXEC l
Some Suggestions on preventing distributed denial of service (DDoS) attacks on Cisco Routers
1. Use the ip verfy unicast reverse-path network interface command
This function checks each packet passing through the router. In the CEF (Cisco Express Forwarding) Table of the router, the
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.