I will talk about two tips, one about monitoring switch port traffic and the other about store value.
1. Monitor switch port traffic
Switch monitoring document in the production environment on the Internet. Therefore, it is complete, and a key knowledge is interspersed in the middle. Zabbix is still innocent .!!! In this demonstration, I used the production environment
Switch Stack-ports displays full port information for the stack switchStacking common, at present in some financial, logistics enterprises are very common, and the other side of the enterprise is not bad money, as long as the program is reasonable, the budget cost is not very small, so here again to emphasize the professional quality of the network workers have been seasoned pre-sales program capabilities.Think of learning as a living habit.---------
Cisco 3750 switch stack configuration points 3750 stack is a real stack, the Catalyst 3550 series uses StackWise technology, it is an innovative stack architecture, A 32 Gbps stack interconnection is provided to connect up to nine switches and integrate them into a unified, logical, and optimized device for convergence, in this way, customers can deploy voice, vi
, and the slot number is different)
Iii. Stack instances:
1: The stacked cables are physically connected. The connection method is master stack1, which is connected to slave stack2.
2: enable the master without any configuration. .
3: Server Load balancer is enabled.
4: No configuration is required. Line plug, automatic stacking election upon startup, master is highlighted)
Note: You can also configure stacks first, such as IP addresses and priorities.
4. Check the current stack status:
Show pla
#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--Cisco Internetwork Operating System SoftwareIOS (tm) C2950 software (c2950-i6q4l2-m), Version 12.1 (9) EA1, RELEASE So
The main function of Port-channel in practical work is to bundle two or more ports into a virtual channel.Interface Port-channel1Description Port (1/0/5-6)Switchport Trunk Encapsulation dot1qSwitchport Trunk allowed VLAN 10Switchport mode Trunk!Interface Port-channel2Description Po
The main function of Port-channel in practical work is to bundle two or more ports into a virtual channel.Interface Port-channel1Description Port (1/0/5-6)Switchport Trunk Encapsulation dot1qSwitchport Trunk allowed VLAN 10Switchport mode Trunk!Interface Port-channel2Description Po
Introduction to Cisco Port Channel)Port trunking is used to bind multiple low-bandwidth ports of a vswitch to a high-bandwidth link to achieve load balancing. Avoid link congestion. Through configuration, You can bind two or four ports to forward data on specific ports to prevent packet loss when the forwarding rate of a single link is too low. Advantages of Trun
GNS3. Eve-ng should also be used with VMware workstation.Eve-ng Installation Tutorial:Software needed: VMware, Eve-ng.ova, WINSCP, SECURECRT, IOU, browser.1: Import the Eve-ng.ova file into VMware. and modify some configuration: memory, CPU, network adapter to change to host-only mode. Network segment to set why you own the same network segment.2: The look after boot. Input Username:root,passwd:eveGet started with some configuration: Modify ROOT_PASSWDConfirm again:Modify hostname:This is follo
Tags: call mode xxxx Virtual div package Data Packet Group EthernetThe main function of Port-channel in practical work is to bundle two or more ports into a virtual channel.Interface Port-channel1Description Port (1/0/5-6)Switchport Trunk Encapsulation dot1qSwitchport Trunk allowed VLAN 10Switchport mode Trunk!Interface Port
24-port full-Gigabit Switch forwarding performance and line-end congestion tests. The current 24-port full-Gigabit Switch market is in great competition, some may not know the forwarding Performance Test and line congestion test of 24 full gigabit switches. After reading the
Server, web server, email server, network device, SQL Server, file server, and printer.
3. view all network devices in one graph
Prtg network monitor can be used to monitor network devices, classify these devices, and view them in a unified graph. In other words, in a graph, you can immediately view the alarms, CPU loads, and response times displayed on the Windows network.
4. Use email or short message service to send a warning
5. Monitor applications on the network and other servers, such as
In order to manage a network, the network grasping the packet Analyzer is essential, but now is no longer the hub era, grab bag is not so easy, but there is always a way to mirror the port, the other port data copy to the port you specify, so you can grab the bag. Today is not about grabbing bags, It is mainly about how to configure the
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.