Topology map:
1. Configure the router R4 as a Frame relay switch
Frame-relay switching * configured as Frame Relay switch
2. Configure the interface's clock frequency, package type, LMI type and Frame Relay DCE on the router R4
int s0/0
No shut
Clock rate 64000 * Set clock frequency
Encapsulation Frame-relay * Encapsulated as Frame Relay
Frame-relay lmi-type
Cisco switch,
Cisco switchesSwitch> enable
Switch # con
Switch # conf
Switch # configure ter
Switch # configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
The combination of Huawei S2000-HI switch and cisco acs for certificationCase: Huawei S2000-HI switch and cisco acs combined certification I. Networking requirements: a company's internal network adopts unified management, send the authentication tasks for accounts and passwords of all devices to the Radius server (ACS
Layer-3 Switch for Cisco switches
Although single-arm routing solves the communication problem between different VLANs, it also has its fatal defects:
-The single arm itself is the Backbone link of the network, which is easy to form a network bottleneck.
-The sub-interface relies on physical interfaces, and the application is not flexible
-You need to view the route table for each vlan forwarding, wasting
"hard" operations on network devices. The security factor is high, but the obtained information is not accurate. For example, if the IP address of a server has been changed, we can think that the server is not connected to the network because the original IP address cannot be found on the switch. The system administrator first checks the IP address information on the server, and then finds out which port of the s
#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--Cisco Internetwork Operating
): can only receive or send bpdus messages
learning (learning) : can receive or send BPDU Message, and form mac
forwarding (Forwarding) : can receive or send BPDU Message, and form mac Address table, send and receive data frames simultaneously
STP Convergence: All ports on the switch are converted to forwarding or blocking mode, which takes 50 seconds by default. The
)
--------------------------------------------------------------------------------
Add Catalyst 5002 to the domain
You need to add Catalyst 5002 To The VTP management domain named cisco and set it to VTP client. It will receive VTP configurations and updates from the VTP server.
Note: by default, the Catalyst 5000 series switches are VTP servers.
Cat5002> (enable)
Cat5002> set vtp domain cisco mode client
T
and a switch are connected with the console lineHow it works: Switch password recovery fundamentals: Change the Config.text file name in the switch to a different file name, and then enter the configuration mode to change the password, and finally restore the Config.text file nameSteps:1. Power off first2. Power off while holding down the mode key on the
Lab Environment:650) this.width=650; "alt=" Cisco Packet Tracert three-tier switch VLAN configuration-Ibm.chick-mingkang.zhou "src=" Http://img2.ph.126.net/2N Qfixjyba1gdiqtbuknhq==/6630601572768576164.png "style=" border:0px;height:auto;margin:0px 10px 0px 0px; "/>Experimental Purpose:1, the three layer switch divides three VLANs, is Vlan2\vnal3\vlan4, and the V
Tags: Cisco MDS zone san Configure a Cisco MDS Optical Fiber storage switch (MDS multilayer Director Switch multi-layer optical fiber array switch)General process: 1: Create a vsan, add the port to vsan2: create a zone, add the port to zone3: Create a zoneset, add the zon
When configuring the Cisco 3560 switch in the morning with the Cisco Packet Tracer practice, it is found that the IP address of the port cannot be configured in port configuration mode.Switch>Switch>enableSwitch#configure TerminalSwitch (config) #interface F0/1Switch (config-if) #?DhcpOnly DHCP commands are available.
Basic configuration and management of the Cisco PT Simulation Experiment (1) switchExperimental Purpose : Master the basic configuration and management of the switch, and understand the basic commands of the switch configuration. Experimental background : A company has a new batch of two-layer switch, before formally p
Recently, the OS of a vswitch is old, so I want to update it. I want to ask a user to update the OS. After updating the OS, the problem occurs, I have a password for the OS. Since the password is being used and it is difficult for them to ask for it, I am ready to clear the password. After finding the relevant article on www.cisco.com, cleared successfully. Write down the cleanup process.
Let's talk about the configuration environment first, the switch
Cisco Catalyst Switch configuration and maintenance method. Today's Catalyst Switch topic discusses the introduction of the History st6000 series and the introduction of the Catalyst Switch 5000 Series. There is no difficulty. Hurry into the Wireless World.
LAN switches have evolved from a HUB-based LAN shared in the t
Cisco switch recover master diskRecovering from a Software Failure1. download the system image from the cisco website. The cco account is required. unzip the system image, decompress the unzipping is binary executable binfile Unix using tar-tvf command unzip unix-1 % tar-tvf image_filename.tarunix-1 % ls-l image_filename.bin3. select 96004 at the speed of the con
Pen name is also large, commonly known as the small gameRecently work has become a little different, received their own network engineers exam is almost 2 doors are nearly point on the heart has a lot of depressed and lost, may be doomed to let me have a good reflection on it, for this today self-study review of the past Cisco Cisco Simple Foundation.Cisco commands and H3C are far apart, recalling that
Encapsulation Frame-relay boot Frame Relay Package
Encapsulation Novell-ether rules the Novell unique format used on the network segment
Encapsulation PPP set PPP to the encapsulation method used by the serial port or ISDN interface
Encapsulation SAP rules the Ethernet 802.2 format used on the network segment the Cisco password is SAP
End Exit Configuration mode
Erase Remove flash memory or configure cache
Erase Startup-config Delete the conte
Lab Environment:650) this.width=650; "alt=" Cisco Packet Tracer three-layer switch interrupt Dhcp-ibm.chick-mingkang.zhou "src=" http://img0.ph.126.net/4fx 93s0ahtpaead19pxmyg==/6619563575538146055.jpg "style=" border:0px;height:auto;margin:0px 10px 0px 0px; "/>Experimental Purpose:1, the VLAN is divided on the three layer switching: vlan10\vlan100\vlan200, and the IP is specified as: 192.168.10.254\ 192.16
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.