cisco 3825 ports

-level QoS and other advanced traffic management features to be transplanted from SAN Island to enterprise-level storage networks. Comprehensive Security Framework: supports RADIUS Authentication, SNMPv3, role-based access control, SSH, SFTP, FC-SP, virtual SAN, hardware Partition and access control list. Advanced diagnostics: Provides intelligent diagnostics, protocol decoding, network analysis tools, and integrated call home functions to improve reliability, quickly solve problems, and reduce

Cisco is the one who learns when it comes to networking. So the Cisco complex is very deep, and then the working contact with Cisco devices is few ...about configuring the same port configuration in bulk# # #思科:Interface Range g1/0/x to g1/0/y # # # #就英文的意思, today a set of port ranges ...Switchport mode accessSwitchport Access VLAN 300# # #华为, Hua 3 no? (Some peo

How should we connect to the Cisco router port? Many people want to know the specific role of the control port and the Auxiliary port. The port content is not detailed on the network. Here is just a few words about the port. The Cisco router port has a control port: the control port console port) and the Auxiliary port (AUX port) are two management ports of the

network will be fatal. Therefore, to improve security, the Cisco router sets password management for the Auxiliary port. Therefore, it is recommended that the network administrator do not use the same password as other passwords in password settings. Otherwise, the security of the router is reduced. In short, the Auxiliary port plays an important role in vro management. Generally, the Console port is used only when the vro is configured. In the proce

A few days ago, a switch cascade using a Cisco 2950 switch and a 100MB port of Tp-link 24 ports. Causes the Cascade ports on the Cisco 2950 device to be in use one day later, the next morning when the port shows err-disabled. The network is not working. How to deal with?To view the interface status:GX-SW-2950-01#SH Int

User Access Verification Password: Idc-3750g-12s-01>ping 192.168.50.47 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.50.47, timeout is 2 seconds: !!!!! Success rate is percent (5/5), round-trip Min/avg/max = 1/1/1 ms Hc-3750g-12s-01>sh ARP | In 192.168.50.47 Internet 192.168.50.47 2 0030.4825.4441 ARPA Vlan50 Idc-3750g-12s-01>sh mac address-table Dynamic address 0030.4825.4441 Mac Address Table ------------------------------------------- Vlan Mac Address Ty

"hard" operations on network devices. The security factor is high, but the obtained information is not accurate. For example, if the IP address of a server has been changed, we can think that the server is not connected to the network because the original IP address cannot be found on the switch. The system administrator first checks the IP address information on the server, and then finds out which port of the switch the IP address is located on. The information obtained by this method is very

= "Wkiol1bc3gvsgrk3aaaxogc7-be056.png"/>1. View the corresponding IP via MAC addressRun Show ARP | Include Mac_address650) this.width=650; "src=" Http://s5.51cto.com/wyfs02/M00/7C/F1/wKioL1bdF7bjyfugAAANVIzMq9E942.png "title=" Qq20160307135242.png "alt=" Wkiol1bdf7bjyfugaaanvizmq9e942.png "/>The timeout cleanup time for Arp and Mac two tables is not the same. Use Switch#clear Arp-cache to clear the ARP information table, use Switch#show interfaces gigabitethernet 0/11 to view ARP refresh time ar

1, if know 192.168.1.100 host address, how to view the port of the host connection switchFor use on core switches: show ARP | In 192.168.1.100Internet 192.168.1.100-8480.2D0D.1CCC ARPA Vlan1Know the MAC address of the 192.168.1.100 host through the above2. Use: Test#show mac address-table Address 8480.2D0D.1CCCMac Address Table-------------------------------------------Vlan Mac Address Type Ports---- ----------- -------- -----8480.2D0D.1CCC DYNAMIC GI

Cisco switch in the VLAN how to add multiple ports at a time, this is usually used in the process of our configuration, because if one of the add port, the workload will be very large, so need to add multiple ports at once, the following by the small set of specific operations to introduce 1, first through the Consolo port or telnet to connect the switch to ente