cisco 3850 configuration guide

Cisco Wireless AP Configuration Guide requirements in complex enterprise environments Overview: using Cisco AP to build an enterprise wireless LAN, users' laptops do not need to be added to the AD domain,You can log on to the wireless network. the user name and password of the domain are used for Logon. SSIDS hides the

Https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/7-x/security/configuration/guide/b_ Cisco_nexus_9000_series_nx-os_security_configuration_guide_7x/b_cisco_nexus_9000_series_nx-os_security_ Configuration_guide_7x_chapter_01.html Feature Description Changed in Release Where documented IP ACLs Added IPV6 Wildcard mask support for access lists a

the ports of the corresponding vswitch as required in table 1. To verify our configuration, you can use the show vlan command in privileged mode to display the configuration you just made and check whether it is correct. The above describes the VLAN configuration of the Cisco Catalyst 1900 switch. The VLAN

to say, after you set the password for level 1, you will be asked to enter the password next time you connect to the switch and enter K, this password is the password set for level 1. Level 15 is the privileged mode password that you enter after you enter the enable command. Step 2: Set the VLAN name. Because the four VLANs belong to different switches, the command for VLAN naming is VLAN 'vlan No. 'name' vlan name ', the following code configures VLAN 2, VLAN 3, VLAN 4, and VLAN 5 on the Switc

Application Guide: Cisco PIX Firewall configuration details-Linux Enterprise Application-Linux server application information, the following is a detailed description. In this application guide, the administrator can learn how to set up a new PIX Firewall. You will set passwords, IP addresses, network address resolutio

Let's use an old diagram here to illustrate 6807XL and 6800IA.650) this.width=650; "Src=" Http://s4.51cto.com/wyfs02/M02/86/09/wKiom1ey-16x3iLuAATm_Mc4Eck449.jpg-wh_500x0-wm_3 -wmp_4-s_413653667.jpg "title=" 6800ia Guide sevt.jpg "alt=" Wkiom1ey-16x3iluaatm_mc4eck449.jpg-wh_50 "/>When the configuration is complete, 6800IA is the equivalent of a 6807XL board.Here is a brief description of the

of the Broadband Router. when accessing the internet, our PC will send a connection request to the Broadband Router. Finally, we set the DNS server. This option varies depending on different regions and line suppliers. Here we enter 202.100.96.68. You can select your own broadband line,. After this setting, the PC in the LAN can share the Internet with the Broadband Router. Conclusion: through all the above steps, we can use the Broadband Router to configure shared Internet access. There are ma

" and the vro will be reinitialized. If you have any questions, answer No;6. Type "Enable" (no password, press Enter );7. Change the password (whether encrypted or not ):A. Enter "config mem" or "copy startup-config mem ";B. Enter "write ";C. Enter "config term" and "enable secret 8. Remove the user prompt and password:A. Enter the virtual line Cisco router configuration mode and enter "line vty 0 4 ";B. En

password, press Enter );7. Change the password (whether encrypted or not ):A. Enter "config mem" or "copy startup-config mem ";B. Enter "write ";C. Enter "config term" and "enable secret 8. Remove the user prompt and password:A. Enter the virtual line configuration mode and enter "line vty 0 4 ";B. Enter "password C. Enter "login" to remove the user prompt, Which is login local );9. Press Ctrl-z to finish;10. Enter "write" to save the changes;11. Ent

-if) # channel-group 1 mode desirable Switch (config-if) # end Appendix: Switch (config-if) # channel-group port_channel_number mode {auto | desirable | on} // Add the physical port to an Ethernet channel and determine the PagP mode. 3) layer-2 Ethernet Channel Configuration Switch # configure terminal Switch (config) # interface range fastethernet 5/6-7 (Note: spaces are required) Switch (config-if-range) # channel-group 2

router (config-router) #ip address192.168.254.1 255.255.255.255router (Config-router) #^zrouter#showrrouter#show Iproute/*=part1router1 Basic Configuration */router>enablerouter#conftrouter (config) #inter f0/0 //Enter No. 0 module NO. 0 port (Fast Ethernet interface) Router (config-if) #ip address192.168.2.1255.255.255.0 //Configuration F0/0 Interface Iprouter (config-if) #no shutdown //open port, default

protocol router (config-router) #network 192.168.2.0//Specifies the network that needs to be advertised (located in the routing interface) router ( Config-router) #network 10.254.10.0router (config-router) #exit/*=part3dhcp Relay Agent configuration */ Router (config) #service dhcp //enable DHCP feature router (config) #inter f0/0 //Enter No. 0 module NO. 0 port (Fast Ethernet interface) Router (config-if) #ip HELPER-ADDRESSNBSP;10.254.10.1NBSP;NBSP

(config ) #router NBSP;RIPNBSP;NBSP;NBSP;NBSP;NBSP;NBSP;NBsp;//Entering routing configuration mode - Enable RIP protocol router (config-router) #version 2 //using version 2, RIPV2 protocol router (config-router) #network 192.168.1.0 NBSP;//Specifies the network that needs to be advertised (located in the routing interface) Router (config-router) #network 222.200.105.0router (config-router) #exit/*=part3 static NAT

: On the emulator, you cannot use the show port-security command on a layer 3 switchPC Settings 192.168.1.2//pc0192.168.1.3//pc1192.168.1.4//pc2192.168.1.5//pc3//Subnet mask and gateway 255.255.255.0 192.168.1.1PC (Command prompt cmd) ipconfig//view MAC address of 4 PCs separatelySwitch0 configuration switch>enswitch#conf tswitch (config) #inter rang f0/1-22switch (config-if-range) #switchport mode access/ /config