cisco 550

Through the previous experiment we learned that by configuring VLANs, the terminals under different VLANs could not communicate with each other, but if you wanted to communicate between different VLANs, you would need to configure inter-VLAN routingLayer three switches have the capability of the network layer and can be forwarded via the routing functionNetwork environment1 set the IP address and gateway of the terminal (192.168.1.1 and 192.168.2.1, respectively).2 VLAN is configured under Layer

"Introduction" Within a switched network, it is possible to segment and organize flexibly through VLANs. VLANs can group devices in a LAN. A group of devices in a VLAN communicates as if it were connected to the same line. VLANs are based on logical connections, not physical connections. Types of VLANsThere are many different types of VLANs used in modern networks. Some VLAN types are defined by traffic category. Some other VLAN types are defined by specific features.Data VLAN: used to deliver u

Automatic backup and fallback of Cisco iOS profiles requires the use of the Archive Archive configuration mode feature of iOS. In general, only the version number of iOS has the Archive configuration mode feature in 12.3 (4) Cisco iOS profile automatic backup All commands are as follows: router> Router>enable Router#configure Terminal Router (config) #archive Router (config-archive) #write-memory

Trunk Link Trunk: Same inter-VLAN communication on different switchesHow to play tag tag encapsulationPackage Type: IEEE 802.1q/cisco ISLIEEE 802.1q:4 Bytes, internal encapsulation, publicCisco isl:30 bytes External encapsulation, privateSwitch port configuration mode: Trunk/acces (OFF)/Dynamic desirable/dynamic AutoTwo auto NO mode of operation generally either trunk or accessEthernet Channel: Multiple physical ports to form a logical port for greate

Now that Cisco Nat is flexible, Can Linux implement it? The answer is yes! Linux netfilter is super flexible, and Linux Nat is not flexible because the iptables program is not flexible. xtables-Addons rawnat has taken an important step towards static Nat, iptables restricts the development of static Nat in Linux! So I put aside iptables, first implemented the kernel module based on Netfilter, and then used procfs as the user interface to see how to im

Cisco CCNA Chapter 2 answers for the third semester, Cisco ccna for the third semester 1. Which command line interface (CLI) mode allows users to configure switch parameters such as host name and password? User Execution Mode Privileged Execution Mode Global Configuration Mode Interface Configuration Mode 2.

Configuration example of cisco router and layer-3 Switch environment, cisco layer-3 SwitchSimple environment configuration instance for cisco router layer-3 Switch I. network topology: Ii. configuration command: 1. vro Configuration: Interface FastEthernet0/0 Ip address 10.66.88.222 255.255.255.0 Ip nat outside Duplex auto Speed auto Interface FastEthernet0/1 I

Asa802-k8.binAsa803-k8.binAsa804-k8.binAsa805-k8.binAsa822-k8.binAsa823-k8.binAsa824-k8.binAsa831-k8.binAsa832-k8.binAsa841-k8.binAsa842-k8.binAsa843-k8.binAsa844-1-k8.binAsa845-k8.binAsa846-k8.binAsa847-k8.binAsa901-k8.binAsa902-k8.binAsa903-k8.binAsa903-smp-k8.binAsa904-k8.binAsa904-smp-k8.binAsa911-k8.binAsa911-smp-k8.binAsa912-k8.binAsa912-smp-k8.binAsa913-k8.binAsa914-k8.binAsa915-k8.binAsa915-smp-k8.binAsa916-k8.binAsa944-2-smp-k8.binTake out your phone and scan the QR code below.650) this

gigabit and routing capabilities are not very important, so the two 2948 switches are not used much in actual projects. 2. Mid-range products Let's look at the mid-end products. The 3500 series of mid-end products are widely used and representative. The basic features of the C3500 series switches include a backboard bandwidth of up to 10 Gbps and a forwarding rate of 7.5 Mpps. It supports 250 VLANs, IEEE 802.1Q and ISL Trunking, and CGMP/Gigabit Ethernet switches, optional redundant power su

This article describes how to configure the IOS Firewall on a Cisco router. What should we pay attention to when configuring the firewall? The following article provides detailed answers. Pre-configuration on R1, R2, and R3 R1 (config) # int e0/0R1 (config-if) # ip add 172.16.1.1 255.255.255.0R1 (config-if) # no shR1 (config) # ip route 0.0.0.0 0.0.0.0 172.16.1.2 configure Static RoutingR1 (config) # ^ ZR2 (config) # int e0/0R2 (config-if) # ip ad

, 6800IA is restarting, patiently wait, and then observe.Router#show FexFex Fex Fex FexNumber Description State Model Serial---------------------------------------------------------------------------101 6800ia-48-01 Online c6800ia-48td foc2016s1ndAfter a wait, when you find that the status is online, that the 6800IA is connected to normal, you can configure it!We can see if the interface of IA is added by the show Run command.Router#show Run........................ Also omit the N-line configura

that the admin domain is able to overwrite all branch switches. The Cisco switch is capable of supporting any media as a trunk, and it can use its own ISL tags for relaying. ISL (Inter-Switch link) is a protocol between switches, between switches and routers, and between switches and servers to transfer multiple VLAN information and VLAN data streams, configured with ISL encapsulation via ports directly connected to the switch, The VLAN allocation a

(global configuration mode)S1 (config) #interface vlan 1 --Enter VLAN 1 PortS1 (config-if) #ip address 192.168.1.1 255.255.255.0 --Configure the vlan1 with an IP address so PC1 and S1 can ping interoperabilityS1 (config-if) #no shutdown --activating VLAN 1 PortS1 (config-if) #end --Return to privileged modes1#copy running-config startup-config --Save configuration (from memory RAM to hard disk NVRAM)s1#show running-config --View switch configuration4. Go to PC1 host command line interface(1) F

protocol between as is called the External Gateway Protocol External Gateway Protocol (also called Inter-Domain routing protocol): there are two types of inter-domain routing protocols: externalGateway Protocol (EGP) and Border Gateway Protocol (BGP)2) Dynamic routing according to the algorithm can be divided into: Distance vector routing protocol, link state routing protocolDistance Vector Routing protocol: Select Route RIP,IGRP based on the number of routes that are routed from the source net

(HSRP)Direct Connect Ping PassTarena-r1 (config) #interface f0/0TARENA-R1 (config-if) #standby 1 IP 192.168.1.254TARENA-R1 (config-if) #standby 1 priority 200 PrioritiesTARENA-R1 (config-if) #standby 1 preempt preemptive rightTARENA-R1 (config-if) #standby 1 track F0/1 port trackingTarena-r2 (config) #interface f0/0TARENA-R2 (config-if) #standby 1 IP 192.168.1.254 act as IPTARENA-R2 (config-if) #standby 1 priority 195 PrioritiesTARENA-R2 (config-if) #standby 1 preempt preemptive rightTARENA-R2

Tags: tle simulates a trunk mode ace 51cto fast spanning tree quick typeLoops are present in the network, and all loops are formed due to confusion caused by ambiguous destination paths. The loop has a great impact on the network. Spanning Tree protocol is a good solution to this problem.The idea of spanning a tree protocol topology is that, regardless of the physical connection between switches, the switch can automatically discover a network with no loop topology, and the network of the logica

Cisco configuration instance _ Cisco dual-Egress NAT configuration objective: to simulate the routing function based on the original address policy when a dual-Egress link is available, and access to the external network from different original addresses is realized, in most cases, the vro uses NAT to translate the Intranet address on the external port, so this experiment also uses dual NAT to translate the

Cisco CCNA Chapter 5 answers for the third semester, Cisco ccna for the third semester

Cisco Terminal configuration: (DHCP only)Service DHCPIP DHCP relay information trust-allInterface Vlan4IP address 192.168.4.254 255.255.255.0IP helper-address 10.0.0.11!Interface Vlan6IP address 192.168.6.254 255.255.255.0IP helper-address 10.0.0.11!650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M00/59/7E/wKioL1TUvvqTNu5WAASFSbihEBY376.jpg "title=" 2015-02-06_21-11-28.png "alt=" Wkiol1tuvvqtnu5waasfsbiheby376.jpg "/>2, the common configuration

Introduction after you log in to the CISCO switch, we will need to use some common operations, such as querying, restarting, and so on, where some of the commonly used operations are grouped together. Query HelpIn different modes, we can enter the question mark directly (? You can query all the commands that you can use in the current mode. When entering a command, if you do not remember the full name of the command, enter the first few characters