cisco 550

LAN is not changed, and the configuration and access control list of the external network Port WAN needs to be changed .Increase the configuration of the VPDN. Assuming the username is admin, password 123456, the configuration process is as follows:This case is XX Telecom ADSL PPPoE access, need to use a common ADSL modem and a Cisco 2600 router (dual Ethernet port), IOS 12.2 (), can realize LAN sharing Internet.　　This case configuration is divided i

Tags: process proc ima RAC Technology share static term ADOBy configuring static routes, you can achieve an increase in routing entries for routers in a relatively simple network.However, if there are more than 20 routers in a network, it is difficult to configure static routes to accommodate the complexity of routing entries and changes in the network. At this point we can use the RIP protocol to configure simple dynamic routing, thus reducing the workload.Configuration ideas1 Configure the IP

policy in Router 2, specifying host and port7 The ACL takes effect under the port of the Router 2 Xia Lian serverNetwork topology1 Configuring Router 1 single-arm routing, establishing sub-interfaces and configuring IP addresses, etc.2 Configuring the Switch's VLAN and port type3 Configuring the IP address of the PC4 Configuring the interface address for Router 25 Configure static routes to communicate properly between networks6 Configure the ACL policy on Router 2 to allow PC1 to access the se

port to enable ACL policyNetwork topology1, configure Router 1, turn on the single-arm routing configuration subinterface address and connect the physical interface address of another route and open the port2 Configuring the VLAN of the switch, configuring the port type3 Configuring the IP address of the PC, specifying the gateway4 Configuring router static routing to enable network interoperability5 Create a new ACL policy on the destination router6 Enter the destination port to make the new A

Tags: routing switching technology HSRP working principle three-layer Exchange STP function DHCP serviceFirst, the questionDay 011. What is a Vlan? What does VLAN do? is the interface of the default switch in that VLAN? What kind of Vlan??2. What is Trunk? What is the mode of Trunk? How to negotiate?3. What is the role of EtherChannel?4. What is DHCP? What is the role of DHCP?Day 021. What is the three layer Exchange? What is the difference between a two-layer switch and a three-tier switch and

Day 051. What is NAT? What are the implementation methods?NAT (Network address translation): By translating the private IP address of the internal network into the world's only public IP address, the internal network canTo connect to an external network such as the Internet.How NAT is implemented:The corresponding relationship of the IP address is one-to-one, and is constant, with the help of the static transformation, it can realize some specific service in the external network.Access to the se

Using Cisco to build an experimental environment I.. Configure DHCP client;Two, configure the switch SW1SW1 (config) #vlan 10SW1 (Config-vlan) #exSW1 (config) #vlan 20SW1 (Config-vlan) #exSW1 (config) #int FA0/1SW1 (config-if) #switchport mode accessSW1 (config-if) #switchport Access VLAN 10SW1 (config-if) #no shutdownSW1 (config) #int FA0/2SW1 (config-if) #switchport mode accessSW1 (config-if) #switchport Access VLAN 20SW1 (config-if) #eSW1 (config

technology. It can interconnect 16 Cisco switches in the C3500, C2900, and C1900 series and manage them through an IP address. The Cisco Visual Switch Manager (CVSM) software in C3500 can also be used to conveniently set and manage switches through a browser. In terms of gigabit features, C3500 fully supports Gigabit interface cards (GBIC ). Currently, GBIC has three types of 1000 BaseSx, which are applica

(Config-router) #exitIf this is all configured, then use the ping command to test it!Here is a start-up-configuring HSRP Hot Spares:Configure on the active three-layer switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.168.1.254Switch (config-if) #standby 1 priority 200Switch (config-if) #standby 1 track fastethernet 0/2Switch (config-if) #standby 1 preemptConfigure on the backup layer three switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.1

One of my customers has a VPN which I 'd like to access. they provided me with a copy of the Cisco VPN Client for Linux, and a "PCF" configuration file for the client. here's what I had to do to get the Cisco VPN Client working in Linux-and it does work just fine. First we make a directory to put the bits and bobs in alan@hactar:~$ mkdir ciscoalan@hactar:~$ cd cisco