cisco ap commands

Login is to turn on remote login password verification, login local not only requires a password, but also requires the user nameIf you set both login and login Local,login local valid(config-line) #line vty 0 4; Set the number of remote connections, allowing 0 to 41 total five connections(config-line) #password 123; Set Telnet (that is, Telnet) password to 123(Config-line) #login; Turn on remote login password verificationLogin means to open remote login (telnet) password authentication, if not

timeoutSwitch (config) # line consoleSwitch (config-console) # Exec-timeout 60Switch (config) # line vtySwitch (config-line) # Exec-timeout 603. Installation and removal licenseswitch# Install license Bootflash:license-fileswitch# Clear License License-fileswitch# Clear License All4. Disable and enable Telnet and SSHswitch# Config TSwitch (config) # no Telnet server enableSwitch (config) # Telnet Server enableswitch# Config TSwitch (config) # SSH server enableSwitch (config) # no SSH server ena

* Common commands for Cisco routers * 1? Exec? Commands :?

Comparison of Cisco and Huawei basic commandsCisco HuaweiShow displayShow version disp versionNo undoShow run disp current-configurationUsername local-userEnd returnShow start disp saved-configurationExit quitExit logoutCtrl + z quitRouter ripRouter ospfRouter bgpHostname sysnameAccess-list aclWrite saveErase delete0 simple7 cipherLogging info-centerEncapsulation link-protocolExample:Sysname liu-chao \ sets the Host NameInterface Ethernet 0/0 enters i

configurationRouter>enableRouter#configure TerminalRouter (config) #interfiguer f0/0Router (config-if) #ip address 192.168.1.2 255.255.255.0Router (config-if) #no shutdownThen back into privileged modeRouter#write Memory for storageThen test if you can ping the IP of the serverRouter#ping 192.168.1.1Then make a copy.Router#copy Running-config TFTPAddress or name of the remote host[]?192.168.1.1 enter the IP of the server after the question markThen leave the default hit enter to finish.4. Route

Cisco switch Basic configuration: Console Port connectionUser mode hostname#;Privileged mode hostname (config) #;Global configuration mode hostname (CONFIG-IF) #;Switch Password settings:switchgt;enable; Enter privileged modeSwitch#config terminal; Go to global configuration modeSwitch (config) #hostname Csico; Set the host name of the switchSwitch (config) #enable secret csico1; set privileged encryption passwordSwitch (config) #enable password Csico

Configure DHCP server on Cisco Router:---------------------------------------IP dhcp excluded-address 192.168.27.1 192.168.27.50!IP DHCP pool CiscoNetwork 192.168.27.0 255.255.255.0Dns-server 192.168.7.20Domain-name fagorarrasate.netDefault-router 192.168.27.1Configure HTTP Server:---------------------IP HTTP ServerUsername Cisco privilege password CiscoIP HTTP Authentication LocalIP http secure-serverIP ht

Switch command Switch> User mode 1: Enter privileged mode enable Switch> Enable switch# 2: Enter global configuration mode configure terminal Switch> Enable Switch#configure Terminal Switch (conf) # 3: Switch name hostname aptech2950 Take aptech2950 as an example Switch> Enable Switch#configure Terminal Switch (conf) #hostname aptch-2950 aptech2950 (CONF) # 4: Configure enable password enable password Cisco for example Switch> Enable S

password, default network device Telnet featureis turned off and is automatically opened after a password is provided.RL (config) # enable password Cisco configuration Enter the password for Enable mode, case sensitiveRL (config) # enable secret Ciscocisco Configure the password to enter enable mode, which is an encrypted password,Show run is invisible.RL (config) # line console 0RL (config-line) # LoginRL (config-line) # password

Tags: Cisco switchBasic configuration and management of switches• Technical Principles• The switch is managed in two basic ways: in-band management and out-of-band management.• The console port management switch through the switch is out-of-band management, which does not occupy the network port of the switch, and the first configuration switch must be configured with the console port.• In-band management via remote telnet, dialing, etc.• The switch's