Alibabacloud.com offers a wide variety of articles about cisco asa 5512 configuration example, easily find your cisco asa 5512 configuration example information here online.
accessed through the extranet IP.To turn on NAT:Global (outside) 1 interfaceNat (inside) 1 192.168.3.0 255.255.255.0Do port mapping:static (inside,outside) TCP interface 192.168.3.222 3389 netmask 255.255.255.255To do access control for an external network port:Access-list outside_access Extended permit IP any anyAccess-group Outside_access in Interface OutsideThe above directive realizes, the external network user accesses the internal terminal through the public network IP, but the intranet u
Cisco ASA Advanced Configuration first, to prevent IP Shard Attack 1 , Ip the principle of sharding; 2 , Ip security issues with sharding; 3 , Prevention Ip Shards. these three questions have been described in detail before and are not introduced here. For more information, please check the previous article:IP sharding principle and analysis. Second, URL Filter
Cisco's ASA Firewall is a stateful firewall that maintains a connection table (conn) about user information, by default the ASA provides stateful connections to TCP and UDP traffic, and is non-stateful to the ICMP protocol.The message traversal process for Cisco ASA is as follows:A new TCP message view to establish the
Cisco Firewall ASA Configuration case
Topology map
Requirements: Through Cisco Firewall ASA use intranet users can access the external network and the server in the DMZ, the server in the DMZ can be published to the network, for the extranet user access
A The use of
There are many VPN products on the Cisco ASA Web VPN configuration market and their technologies are different. For example, in the traditional IPSec VPN, SSL allows the company to achieve more remote users to access the VPN in different locations, this service enables more network resources to be accessed and has low
Cisco ASA L2TP over IPSEC configuration details
1. Create a VPN address pool
Ciscoasa (config) # ip local pool vpnpool 192.168.151.11-192.168.151.15 mask 255.255.255.0
2. Configure the Ipsec encryption algorithms 3DES and SHA.
Ciscoasa (config) # crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des (esp-sha-hmac)
3. Set the IPSec transmission mode to transport.
Step 1 of Cisco ASA firewall VPN configuration: Create an address pool. To remotely access the client, you need to assign an IP address during logon. Therefore, we also need to create a DHCP address pool for these clients. However, if you have a DHCP server, you can also use a DHCP server. QUANMA-T (config) # ip local pool vpnpool 192.168.10.100-192.168.10.199 ma
connection type to remote access.Tunnel-group vpnclient general-attributes//Configuring the authentication method for this channel groupAddress-pool vpnclient//define the address pool usedDefault-group-policy vpnclient//define default Group Policy-----Set up authentication methods and shared keys-------------Tunnel-group vpnclient ipsec-attributes//Configure authentication method for IPSecPre-shared-key *//Pre-shared key for IKE connectionTelnet Timeout 5//telnet timeout settingSSH 0.0.0.0 0.0.
TopologyRequirement: You can use the Cisco Firewall ASA to access servers in the Internet and DMZ through the Intranet. servers in DMZ can be published to the network for access by Internet users.I. Use of Cisco simulated FirewallBecause we do not have real devices, we use a virtual system using the Linux kernel to simulate Cisco's firewall. The simulated firewal
Configuration example of cisco router and layer-3 Switch environment, cisco layer-3 SwitchSimple environment configuration instance for cisco router layer-3 Switch
I. network topology:
Ii. c
I came back again, the last two articles introduced the Huawei Stack, third firewall IRF. This time to introduce the Cisco stack (stack), although the implementation of the idea is consistent, but the configuration there is a need to pay attention to the place, especially now do the two-tier operators of the network workers, all the producers will be, the pressure is really big.First, the topological enviro
An example of Cisco Easy VPN comprehensive configuration is shown in this example. The topology is 15-15. In this example, the Cisco 831 router is used as the remote device of Easy VPN and the
4.2 related configuration of access switches# # In this example, we are connecting to an access switch where the GI0/1 port is allied to the core switch. It also means that we need to configure GI0/1 as trunk port. The specific configuration is as follows:D-2960-3 (config) #int GI0/1D-2960-3 (config-if) #swD-2960-3 (config-if) #switchport moD-2960-3 (config-if) #
Vswitch span technology Overview + Cisco configuration example
1. Introduction to span
The span technology is mainly used to monitor data streams on vswitches. It can be divided into two types: Local span and remote span.---- Local Switched Port Analyzer (SPAN) and remote span (rspan) have slightly different implementation methods.
Using the span technology, we c
the other two similar networks.How to configure the GRE tunnel?
Configuring the GRE tunnel on a Cisco router is a simple task. You only need to enter several lines of commands. The following is a simple example.
Router:
Interface ethernet0/1IP address 10.2.2.1 255.255.255.0
Interface serial0/0IP address 192.168.4.1 255.255.255.0
Interface tunnel0IP address 1.1.1.2 255.255.255.0Tunnel source serial0/0Tunnel
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.