When Cisco routers are routed first, when Nat first may be known, inside is routed first, outside is first Nat.Well, for Cisco ASA, it is not the case, most of the first to find the route if the data from inside, in both cases Nat will first route to confirm the interface.
Did the purpose NAT conversion
St
Cisco ASA Advanced Configuration first, to prevent IP Shard Attack 1 , Ip the principle of sharding; 2 , Ip security issues with sharding; 3 , Prevention Ip Shards. these three questions have been described in detail before and are not introduced here. For more information, please check the previous article:IP sharding principle and analysis. Second, URL Filter Use AS
accessed through the extranet IP.To turn on NAT:Global (outside) 1 interfaceNat (inside) 1 192.168.3.0 255.255.255.0Do port mapping:static (inside,outside) TCP interface 192.168.3.222 3389 netmask 255.255.255.255To do access control for an external network port:Access-list outside_access Extended permit IP any anyAccess-group Outside_access in Interface OutsideThe above directive realizes, the external net
For many years, Cisco PIX has been a firewall established by Cisco. In May 2005, however, Cisco launched a new product, the Asa,adaptive security appliance, as an adaptive safety product. However, PIX is still available. I've heard a lot of people asking about the difference between the two product lines on a number of
For many years, Cisco PIX has been a firewall established by Cisco. In May 2005, however, Cisco launched a new product, the Asa,adaptive security appliance, as an adaptive safety product. However, PIX is still available. I've heard a lot of people asking about the difference between the two product lines on a number of
In this article, I'll briefly explain the Active/standby failover configuration on the Cisco ASA. The lab is do in GNS3.
Physical topology:
ConfigurationCiscoasa/act/pri (config) # sh run failoverFailoverFailover LAN Unit PrimaryFailover LAN Interface failover_stateless GIGABITETHERNET0/2Failover link failover_stateful gigabitethernet0/1Failover
Cisco's ASA Firewall is a stateful firewall that maintains a connection table (conn) about user information, by default the ASA provides stateful connections to TCP and UDP traffic, and is non-stateful to the ICMP protocol.The message traversal process for Cisco ASA is as follows:A new TCP message view to establish the
Cisco ASA failover Command Injection Vulnerability (CVE-2015-0675)
Release date:Updated on:
Affected Systems:Cisco ASA 1, 5500Description:CVE (CAN) ID: CVE-2015-0675
The Cisco ASA 5500 Series Adaptive Security Device is a modular platform for providing security and VPN se
ASA-防火墙-cisco
The role of the ASA firewall1, in the network to isolate dangerous traffic, no point.The principle of the ASA firewall1. Distinguish different areas by security level: internal area, external area, demilitarized zone.By default: High-level traffic can go to lower levels,Low-level traffic c
Cisco ASA iOS upgrade or RestoreFirst, pre-upgrade preparation work1 , prepare the iOS file you want to upgrade and the corresponding ASDM file2 , set up TFTP on a computer, configure the directory, and connect to the firewall (assuming the computer IP is 192.168.1.2)Second, upgrade steps1 , Telnet on the ASAasa>en// Enter privileged modeAsa#conft// Enter configuration mode2 , viewing files on the
Cisco ASA iOS Upgrade or RestoreFirst, pre-upgrade preparation work1. Prepare the iOS files to be upgraded and the corresponding ASDM files2. Set up TFTP on a computer, setup the directory, and connect with the firewall (assuming the computer IP is 192.168.1.2)Second, upgrade steps1 , Telnet on the ASAasa>en//Enter privileged modeAsa#conft//Enter configuration mode2 , viewing files on the
This is certainly not the first article on "Quick Guide to building a VPN using Cisco devices, however, we still hope that this guide will become an all-in-one guide for users who use ASA 5505 devices to set up VPN and connect to the Internet.
The ASA itself has a setup wizard, but this wizard does not cover all aspects of work required by the user, and some step
1, the experimental topology diagram :650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M01/59/49/wKioL1TPCfbgwIOLAACCEDU0i5M014.jpg "title=" Untitled. jpg "alt=" wkiol1tpcfbgwiolaaccedu0i5m014.jpg "/>1. Experiment Description :R1 as a company's site 1, the internal 1.1.1.1/32 Server needs a company site 2 of the administrator to implement remote telnet of equipment management;R5 as a company's site 2, the internal 2.2.2.2/32 Server needs a company site 1 of the administrator to implemen
TopologyRequirement: You can use the Cisco Firewall ASA to access servers in the Internet and DMZ through the Intranet. servers in DMZ can be published to the network for access by Internet users.I. Use of Cisco simulated FirewallBecause we do not have real devices, we use a virtual system using the Linux kernel to simulate Cisco's firewall. The simulated firewal
In actual cases also encountered this kind of problem, the customer intranet has a server map on the Internet, extranet user access Global-ip no problem, but intranet users want to access Global-ip will not pass, typical is the user will intranet server made public network DNS a record, Both internal and external networks are accessed through domain names.JUNIPER series equipment including NETSCREEN/ISG/SSG no such problems, directly through the ordinary dip can be achieved, the subsequent produ
Step 1 of Cisco ASA firewall VPN configuration: Create an address pool. To remotely access the client, you need to assign an IP address during logon. Therefore, we also need to create a DHCP address pool for these clients. However, if you have a DHCP server, you can also use a DHCP server. QUANMA-T (config) # ip local pool vpnpool 192.168.10.100-192.168.10.199 mask 255.255.255.0 Step 2: Create IKE Phase 1.
Cisco ASA L2TP over IPSEC configuration details
1. Create a VPN address pool
Ciscoasa (config) # ip local pool vpnpool 192.168.151.11-192.168.151.15 mask 255.255.255.0
2. Configure the Ipsec encryption algorithms 3DES and SHA.
Ciscoasa (config) # crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des (esp-sha-hmac)
3. Set the IPSec transmission mode to transport. The default mode is tunnel (L2TP only suppor
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.