Cisco's ASA Firewall is a stateful firewall that maintains a connection table (conn) about user information, by default the ASA provides stateful connections to TCP and UDP traffic, and is non-stateful to the ICMP protocol.The message traversal process for Cisco ASA is as follows:A new TCP message view to establish the
Cisco asa vpn xml Parser Denial of Service Vulnerability (CVE-2015-0677)Cisco asa vpn xml Parser Denial of Service Vulnerability (CVE-2015-0677)
Release date:Updated on:Affected Systems:
Cisco ASA 1, 5500
Description:
CVE (C
1. Configure NAT translation for a public network address poolNat (inside) 1 10.0.0.0 255.255.255.0Global (Outside) 1 222.172.200.20-222.172.200.30//This command may not work? And the TAB key is not complete, but no tube, according to lose can.OrGlobal (outside) 1 222.172.200.202, the public network only 1 fixed IP NAT conversionNat (inside) 1 10.0.0.0 255.255.255.0Global (Outside) 1 222.172.200.68//Designa
TopologyRequirement: You can use the Cisco Firewall ASA to access servers in the Internet and DMZ through the Intranet. servers in DMZ can be published to the network for access by Internet users.I. Use of Cisco simulated FirewallBecause we do not have real devices, we use a virtual system using the Linux kernel to simulate Cisco's firewall. The simulated firewal
Step 1 of Cisco ASA firewall VPN configuration: Create an address pool. To remotely access the client, you need to assign an IP address during logon. Therefore, we also need to create a DHCP address pool for these clients. However, if you have a DHCP server, you can also use a DHCP server. QUANMA-T (config) # ip local pool vpnpool 192.168.10.100-192.168.10.199 mask 255.255.255.0 Step 2: Create IKE Phase 1.
Release date:Updated on:
Affected Systems:Cisco ASA 5500 Series Adaptive Security Appliance 8.0-8.4Description:--------------------------------------------------------------------------------Cve id: CVE-2011-3285
The Cisco ASA 5500 Series Adaptive Security Device is a modular platform for providing security and VPN services. It provides firewall, IPS, anti-X, a
Cisco ASA L2TP over IPSEC configuration details
1. Create a VPN address pool
Ciscoasa (config) # ip local pool vpnpool 192.168.151.11-192.168.151.15 mask 255.255.255.0
2. Configure the Ipsec encryption algorithms 3DES and SHA.
Ciscoasa (config) # crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des (esp-sha-hmac)
3. Set the IPSec transmission mode to transport. The default mode is tunnel (L2TP only suppor
In this article, I'll briefly explain the Active/standby failover configuration on the Cisco ASA. The lab is do in GNS3.
Physical topology:
ConfigurationCiscoasa/act/pri (config) # sh run failoverFailoverFailover LAN Unit PrimaryFailover LAN Interface failover_stateless GIGABITETHERNET0/2Failover link failover_stateful gigabitethernet0/1Failover interface IP failover_stateless 169.254.0.15 255.255.255
Understand Cisco NATA lot of things have happened to configure a NAT.1. Inside and OutsideMany people who have configured NAT in Cisco have a question, that is, the difference between inside and outside! The following describes the NAT execution sequence in the
Cisco ASA iOS upgrade or RestoreFirst, pre-upgrade preparation work1 , prepare the iOS file you want to upgrade and the corresponding ASDM file2 , set up TFTP on a computer, configure the directory, and connect to the firewall (assuming the computer IP is 192.168.1.2)Second, upgrade steps1 , Telnet on the ASAasa>en// Enter privileged modeAsa#conft// Enter configuration mode2 , viewing files on the
Release date:Updated on:
Affected Systems:Cisco ASA Description:--------------------------------------------------------------------------------CVE (CAN) ID: CVE-2014-0653, CVE-2014-0655
The Cisco ASA 5500 Series Adaptive Security Device is a modular platform for providing security and VPN services. It provides firewall, IPS, anti-X, and VPN services.
A Security
Cisco ASA iOS Upgrade or RestoreFirst, pre-upgrade preparation work1. Prepare the iOS files to be upgraded and the corresponding ASDM files2. Set up TFTP on a computer, setup the directory, and connect with the firewall (assuming the computer IP is 192.168.1.2)Second, upgrade steps1 , Telnet on the ASAasa>en//Enter privileged modeAsa#conft//Enter configuration mode2 , viewing files on the
Cisco Firewall ASA Configuration case
Topology map
Requirements: Through Cisco Firewall ASA use intranet users can access the external network and the server in the DMZ, the server in the DMZ can be published to the network, for the extranet user access
A The use of Cisco
Cisco configuration instance _ Cisco dual-Egress NAT configuration objective: to simulate the routing function based on the original address policy when a dual-Egress link is available, and access to the external network from different original addresses is realized, in most cases, the vro uses NAT to translate the Int
Company A Cisco asa5505 collapsed, fortunately there is a standby machine, but before the other people have used, do not know the login password, so take out the console line access to the standby 5505, re-power, press ESC at startup, then the prompt Rommon #0 >The value of the configuration register is 0x41 Rommon #0 >confreg 0x41Enter reboot, restart the device Rommon #1 >rebootThe process of entering a password is skipped after restarting the devic
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.