Alibabacloud.com offers a wide variety of articles about cisco catalyst 3550 switch, easily find your cisco catalyst 3550 switch information here online.
Figure Cisco Catalyst 3550 series smart Ethernet switches are a new type of enterprise-class stackable multi-layer switch that provides high availability, high scalability, and high security, and improves the management capabilities of network operations. With a series of Fast Ethernet and Gigabit Ethernet config
/17 Cisco (config-if) # ip access-group 6 in Cisco (config) # access-list 6 permit 10.138.208.81 In this way, the FastEthernet0/17 port of the vswitch is bound to ip Address: 10.138.208.81. The most common understanding of port security is to control and manage network traffic based on the MAC address, such as binding a MAC address to a specific port, restrict the number of MAC addresses that a speci
Cisco Catalyst Switch configuration and maintenance method. Today's Catalyst Switch topic discusses the introduction of the History st6000 series and the introduction of the Catalyst Switch
#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--Cisco Internetwork Operating
Cisco 3550 switch stp learning notes STP (Spanning Tree Protocol) (IEEE 802.1D) Spanning Tree Protocol-review the working principles of SW: 1. the frame it forwards cannot be modified. create a MAC-PORT ing table based on source MAC learning. forward the frames in the target MAC ing table directly from the corresponding port. for frames without target MAC ing/Tar
For complete syntax and application information about this chapter, seeCatalyst 3550 Multilayer Switch Command ReferenceAnd Cisco IOS Interface Command Reference For Release 12.1. Understanding Interface Types This section describes different interface types and some reference content for configuring these interfaces in detail in other sections. Other section
1. Unplug the power cord of the vswitch, press the switch Mode button, and re-plug the power cord of the vswitch. Release the Mode button after the LEDs on Port 1x are off. 2. For the Catalyst 2940/2950 L series: Unplug the power cord of the switch, hold down the Mode button of the switch, and re-plug the power cord of
The article I want to share and configure VLAN on Linux through Cisco Catalyst Switch.Requirements:1. Linux installed on a PC with one or more NICs (Network Interface Card). I Use the Centos 5.4 using 2.6.18-164.11.1.EL5PAE kernel. It should is applicable on other Linux distros such as Slackware, Ubuntu, Fedora, Debian, etc.2. Cisco
Found that Cisco Catalyst Switch reboot is always in rommom mode, the system reboots when the Confreg command chooses the startup mode of 1 (starting from the first file) and cannot enter the normal interface. Enter to boot: 0 = Disable Autoboot 1 = the internal flash device 2 = commands specified in ' BOOT ' environment variable [2]: 1 The analysis suggest
Cisco Catalyst 6500 Series Switch Denial of Service Vulnerability (CVE-2015-0771)Cisco Catalyst 6500 Series Switch Denial of Service Vulnerability (CVE-2015-0771) Release date:Updated on:Affected Systems:
If the switch login password is forgotten, don't worry, as long as you have a PC, there are similar HyperTerminal (Hyper Terminal) This is a terminal program, connected to the switch console port, then the password recovery is n simple. 1. For the Catalyst 2900/3500XL series: Disconnect the power cable from the switch
A Cisco 4506 switch in the user's actual environment could not log on, and the system could only be cracked because the maintenance staff did not remember the modified password.Environment:Cisco Catalyst 4506E switch, engine for WS-X45-SUP8-E, system version is cat4500es8-universal-mCrack steps:To restart the
an IGMP exit request, it moves the host port number from the entry of the content addressing memory CAM table. By supporting hardware IGMP listening and implementing IGMP listening configuration through the Cisco cluster management suite, the Catalyst 2950 vswitch provides excellent performance and ease of use when controlling and managing LAN multicast applications. C
This article describes how to configure a vswitch for a CISCO 3550 router and how to configure access control for a MAC address. In network management, users often encounter this situation: some users violate management regulations and modify their own IP addresses without permission to access restricted resources. Such behavior not only undermines information security rules, but may also cause network comm
For details about how to configure DHCP for a CISCO 3550 switch, refer to some configuration content in this article for comparison and learning. After "ip helper-address dhcp server ADDRESS" according to the configuration described on the Internet, the project finds that the client cannot obtain the ip address from the DHCP server, I recently configured
(POTS), digital telephone and ISDN traffic on the same media, or with Asymmetric Digital user line (ADSL) in the same line bundle, therefore, service providers can configure LRE for buildings that already use broadband services. Product Overview The Cisco Catalyst 2950 LRE Ethernet switch is a fixed configuration and stackable mode that provides wire speed LRE a
a very important application, which will prompt the IT team to rethink the Network Design of San Jose headquarters. Network convergence-transmitting data and voice over the same network-will save Cisco's long-term expenditure and serve as a platform for future development. However, in the short term, it will put heavy pressure on a diverse platform that forms the Cisco network infrastructure. Cisco
-T line cards for copper cable options when a media converter is used. Features and advantages Transparent Functions The Catalyst 4500 series switches provide a series of modules that support the combination of a large number of speeds and physical media. These line cards are transparent; all group processing, sorting, buffering, and QoS are performed in the exchange management engine. To this end, the line card utilizes the features and functions of
Cisco's flagship Switch replaces the new brain with the new IOS software modularization to bridge the "operational gap" between IT talent and network service needs ". On April 9, August 29, Cisco Systems announced the launch of a number of software improvements based on Cisco Internet Operating System IOS. These improved IOS software is mainly used in the
Lab Environment:1. Configure two VLAN 10 and VLAN 20VLAN IP address settings: 192.168.10.1 255.255.255.0 (192.168.10.1 is a VLAN 10 gateway address)VLAN IP Address setting: 192.168.20.1 255.255.255.0 (192.168.20.1 is a VLAN 20 gateway address)2. (Windows Server R2 operating system) set up a DHCP server to create two scopes VLAN 10 and VLAN 20,Get the IP address dynamically using VLAN 10 and VLAN 20. The DHCP server NIC accesses the switch FA0/1 port.D
Start building with 50+ products and up to 12 months usage for Elastic Compute Service
1 on 1 presale consultation
24/7 Technical Support 6 Free Tickets per Quarter Faster Response
Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.
A comprehensive suite of global cloud computing services to power your business
Payment Methods We Support
