determines which vro Configuration tool you need. Maybe you have more than 250 users, therefore, Cisco may think that you should have more budget for network management, so it wants to sell you a management tool ).
However, in my managed network, there are 1200 users in 70 different cities, and CNA can be used to manage them well. In fact, this tool also supports many more advanced
Introduction to CISCO router AAA and related routing configuration cisco aaa www.2cto.com 3A concept: authentication authorization Accounting accountingcisco provides a variety of 3A services for routers and switches: 1. Self-contained AAA router/NAS self-contained AAA service NAS (Network Access Server) 2. Contact the AAA service on the
The Cisco Router performs very well in the market. Here we will mainly focus on Cisco routers and explain in detail the detailed steps of Cisco router configuration. Cisco routers are the core devices for network communication, currently, it has been widely used. I will intr
Using the Cisco router configuration can easily implement VoIP, So I studied the statements related to the Cisco router configuration and shared them here, hoping to be useful to everyone. VoIPVoice over IP) is a technology that transmits voice over the Internet. It has grown with the development of Internet technology
Cisco switch by default.
But it can be implemented with only one command, namely: 3550 # terminal monitor. In order to experience the actual effect, we can open two DOS windows on our PC and log on to the same Cisco switch through TELNET.
One is used for monitoring, and the other is used to perform specific operations, as shown below: for example, we execute a p
Recently, I have seen many vpn things and found that many manufacturers are paying attention to the implementation of Dynamic IP address-based vpn for small and medium-sized enterprises. Of course, cisco is no exception. In its ios12.3 (4) T, it began to support dynamic Address Resolution of vpnpeer. Now, in CiscoIOS12.3 (4) T, VPNpee is created based on the DNS name.
Recently, I have seen many vpn things and found that many manufacturers are paying a
Absrtact: This article describes the first time the author contact Cisco PIX Firewall, summed up the Basic Firewall configuration 10 aspects of content.
Hardware firewall, is the network between the wall, to prevent illegal intrusion, filtering information, etc., structurally speaking, is simply a PC-style computer host plus flash (Flash) and firewall operating system. Its hardware is similar to the common
This article mainly uses an example to explain in detail how to solve the packet loss problem caused by CISCO router faults? The following article gives me a detailed answer.
Recently, some people in my department (Department A) reported that they could not access the network of the higher-level department (Department B. I use the ping command from the computer A1 (IP Address: 10.20.12.11/24) used by this p
Cisco routers play a very important role in the routing industry, and there are also a lot of user groups. It is very important to understand some Cisco router security configurations. Currently, most enterprises and departments connect to the Internet. Generally, a router is connected to an ISP.
This router serves as a bridge between the external Internet and the internal network. If this router can proper
vlan configuration informationSwitch # show interface; view port informationSwitch # show int f0/0; view the specified port informationRouter # copy running-config startup-config; Save the ConfigurationRouter # copy running-config tftp; Save the configurationTftprouter # copy startup-config tftp; the boot configuration is savedTftprouter # copy tftp flash:; upload filesFlashrouter # copy tftp startup-confi
When it comes to configuring a new Cisco router, most configurations depend on the type of router and the purpose it will serve. However, each administrator has its own "correct" configuration for each router's list of commands. The author will share with you the list of 10 commands that he has configured the router for himself.
When it comes to configuring a new Cisco
(config) #no monitor session 1Switch (config) #endSwitch#wrSwitch#show MonitorNo SPAN configuration is present in the system.3. Other(1) Port image filtering, port mirroring can do filter.Monitor session session_number Filter VLAN Vlan-id [, |-]* * Specifies which VLANs belong to the traffic that the source port is entering, and can be emitted from the destination port.(2) Delete imageNo monitor session {Session_number | all | local | remote}**SESSIO
configuration information1. When the switch is powered on and started, press and hold the Sys Req button on the back panel of the switch for 5 seconds, and then release it;2. Go to the configuration menu and select "Clear Non-Volatile RAM" to Clear all Cisco router configuration information including passwords of the
It is also helpful to understand some of the knowledge about switch configuration, and here we explain the main statements and procedures for Cisco switch configuration. Last talk with you about how to properly connect the switch, today with some configuration clips to introduce the port
Router Access ADSL configuration detailed
1, Cisco router connection to the ADSL modem configuration: Note: The case for Beijing Telecom ADSL PPPoE access, need to use a common ADSL modem and a Cisco 2500 router (dual Ethernet port), IOS 12.2 (T), Be able to realize LAN sharing Internet. This case
A Cisco router uses Cisco 3620 as the ios dhcp Server. the IP address of the fastethernet0 port connected to the Intranet is 192.168.1.4, And the L2 Switch uses two Cisco 2950, A layer-3 Switch uses a Cisco 3550. There are two VLANs in the network. To simplify the description, assume that each VLAN uses a 24-bit networ
It's classic. I use it.DeploymentsThe deployments in this document were implemented in an isolated lab environment. the deployments were cleared by issuing the write erase command on the routers, and the clear config all command on the switches to ensure that all devices have a default configuration. make sure you understand the potential impact of any configuration or command on your network before using i
As a port device connecting WAN, vrouters have been widely used. Their main function is to connect multiple independent networks or subnets to achieve optimal routing and datagram transmission between the Internet. This article takes the Cisco 2511 vro as an example to introduce four router configuration methods.
1. Use the C
#config terminal
Route (config) # line vty 0 4 ---- enter telnet remote login port mode (0 4 allows 5 Users)
Route (config-line) # password CISCO ---- set the password to "CISCO" (to encrypt the password, enable vro password protection before: service pass-encryption)
Route (config-line) # login ---- encrypted upon login
Route(config-line)#exit
Continue to enter the privileged mode and wh
192.168.61.128 as the remote server IP address of GNS3, perhaps everyone is more curious about the configuration of the address there is no need to pay attention to the place, the answer is there, as long as the IP address to the IOU virtual machine IP address.In fact, this place is currently reserved for IOU settings. You can simply think that GNS3 can not only use the local dynamips as iOS running server, it can also designate a remote UNIX virtual
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.