cisco global

policy in Router 2, specifying host and port7 The ACL takes effect under the port of the Router 2 Xia Lian serverNetwork topology1 Configuring Router 1 single-arm routing, establishing sub-interfaces and configuring IP addresses, etc.2 Configuring the Switch's VLAN and port type3 Configuring the IP address of the PC4 Configuring the interface address for Router 25 Configure static routes to communicate properly between networks6 Configure the ACL policy on Router 2 to allow PC1 to access the se

port to enable ACL policyNetwork topology1, configure Router 1, turn on the single-arm routing configuration subinterface address and connect the physical interface address of another route and open the port2 Configuring the VLAN of the switch, configuring the port type3 Configuring the IP address of the PC, specifying the gateway4 Configuring router static routing to enable network interoperability5 Create a new ACL policy on the destination router6 Enter the destination port to make the new A

Tags: routing switching technology HSRP working principle three-layer Exchange STP function DHCP serviceFirst, the questionDay 011. What is a Vlan? What does VLAN do? is the interface of the default switch in that VLAN? What kind of Vlan??2. What is Trunk? What is the mode of Trunk? How to negotiate?3. What is the role of EtherChannel?4. What is DHCP? What is the role of DHCP?Day 021. What is the three layer Exchange? What is the difference between a two-layer switch and a three-tier switch and

Day 051. What is NAT? What are the implementation methods?NAT (Network address translation): By translating the private IP address of the internal network into the world's only public IP address, the internal network canTo connect to an external network such as the Internet.How NAT is implemented:The corresponding relationship of the IP address is one-to-one, and is constant, with the help of the static transformation, it can realize some specific service in the external network.Access to the se

Using Cisco to build an experimental environment I.. Configure DHCP client;Two, configure the switch SW1SW1 (config) #vlan 10SW1 (Config-vlan) #exSW1 (config) #vlan 20SW1 (Config-vlan) #exSW1 (config) #int FA0/1SW1 (config-if) #switchport mode accessSW1 (config-if) #switchport Access VLAN 10SW1 (config-if) #no shutdownSW1 (config) #int FA0/2SW1 (config-if) #switchport mode accessSW1 (config-if) #switchport Access VLAN 20SW1 (config-if) #eSW1 (config

This article describes how to configure the IOS Firewall on a Cisco router. What should we pay attention to when configuring the firewall? The following article provides detailed answers. Pre-configuration on R1, R2, and R3 R1 (config) # int e0/0R1 (config-if) # ip add 172.16.1.1 255.255.255.0R1 (config-if) # no shR1 (config) # ip route 0.0.0.0 0.0.0.0 172.16.1.2 configure Static RoutingR1 (config) # ^ ZR2 (config) # int e0/0R2 (config-if) # ip ad

, 6800IA is restarting, patiently wait, and then observe.Router#show FexFex Fex Fex FexNumber Description State Model Serial---------------------------------------------------------------------------101 6800ia-48-01 Online c6800ia-48td foc2016s1ndAfter a wait, when you find that the status is online, that the 6800IA is connected to normal, you can configure it!We can see if the interface of IA is added by the show Run command.Router#show Run........................ Also omit the N-line configura

that the admin domain is able to overwrite all branch switches. The Cisco switch is capable of supporting any media as a trunk, and it can use its own ISL tags for relaying. ISL (Inter-Switch link) is a protocol between switches, between switches and routers, and between switches and servers to transfer multiple VLAN information and VLAN data streams, configured with ISL encapsulation via ports directly connected to the switch, The VLAN allocation a

protocol between as is called the External Gateway Protocol External Gateway Protocol (also called Inter-Domain routing protocol): there are two types of inter-domain routing protocols: externalGateway Protocol (EGP) and Border Gateway Protocol (BGP)2) Dynamic routing according to the algorithm can be divided into: Distance vector routing protocol, link state routing protocolDistance Vector Routing protocol: Select Route RIP,IGRP based on the number of routes that are routed from the source net

Automatic backup and fallback of Cisco iOS profiles requires the use of the Archive Archive configuration mode feature of iOS. In general, only the version number of iOS has the Archive configuration mode feature in 12.3 (4) Cisco iOS profile automatic backup All commands are as follows: router> Router>enable Router#configure Terminal Router (config) #archive Router (config-archive) #write-memory

Trunk Link Trunk: Same inter-VLAN communication on different switchesHow to play tag tag encapsulationPackage Type: IEEE 802.1q/cisco ISLIEEE 802.1q:4 Bytes, internal encapsulation, publicCisco isl:30 bytes External encapsulation, privateSwitch port configuration mode: Trunk/acces (OFF)/Dynamic desirable/dynamic AutoTwo auto NO mode of operation generally either trunk or accessEthernet Channel: Multiple physical ports to form a logical port for greate

discover the configuration file. Therefore, the following command should be used to turn off the feature: Router (config) #no Service config14, close no based on ARPMost Cisco routers (by default) send out unfounded ARP messages, regardless of when the client connects and negotiates an IP address based on the PPP connection. This ARP message is the main use of ARP poison attacks.Even if the client receives an address from a local address pool, the

An example of Cisco Easy VPN comprehensive configuration is shown in this example. The topology is 15-15. In this example, the Cisco 831 router is used as the remote device of Easy VPN and the Cisco 1751 router is used as the device of Easy VPN Server. In this example, the WAN interface IP addresses of the Cisco 1751 r

following command: Global mode: from privileged mode, we can enter global mode. In this mode, you can change the entire configuration of the vro. If you need to change the configuration, you need the following command. This is an example of how to enter the global mode. By default, if you do not set a password for the Cisco