cisco linksys router password

Huawei router and the same class Cisco router in the functional characteristics and configuration interface is completely consistent, some aspects also according to the needs of domestic users made a good improvement. For example, in English and Chinese can be switched configuration and debugging interface, so that users do not have to face a large pile of Englis

Initial installation of the CISCO router tutorial During the first installation, the system automatically enters the Dialog Setup, as prompted on the screen, answer the router name, encrypted super login password, super login password, remote login

CHAP (Challenge Handshake Authentication Protocol) and PAP (Password Authentication Protocol) are generally used to provide security Authentication on PPP encapsulated serial lines. With CHAP and PAP authentication, each Cisco router is identified by a name to prevent unauthorized access. Task commands Set the PPP encapsulation ppp1 Set the authentication method

the devices connected to the internet have a ground wire. These devices include hosts, workstations, hubs, switches, routers, and MODEM connected To routers. The terminal or PC that configures the router must also use a valid power supply. CISCO synchronous serial interfaces are commonly used. Different interfaces, such as RS232 and V.35, can be obtained through different cables. In addition, the cables of

:(1) Step 1: Configure the Router Ethernet interface IP address(2) Step 2: Configure the router password(3) Step 3: Access the router via TelnetCommands for the relevant steps:Configure the Router Ethernet interface IP address (enter the privileged mode, global mode, interfa

255.255.255.0 IP nat outside no IP mroute-cache Bandwidth 2000 No Fair-queue clockrate 2000000 Interface Serial1 No IP address shutdown No IP classless IP route 0.0.0.0 0.0.0.0 Serial0 access-list 1 Permit 10.1.1.0 0.0.0.255 Line con 0 line aux 0 Line vty 0 4 password Cisco End 3, multiplex dynamic address conversion applicable environment: Dynamic Address Translation is

privileged mode, you must set a privileged mode password or configure telnet user rightsConfigure the Vty line login password and enable global password encryptionLog on to the router with the Telnet command to seeDisplay current configuration informationPC0 setting 192.168.1.2255.255.255.0192.168.1.1Router0 configura

Telnet remote Login Configuration 1, configure Cisco router login account, password, account level, as shown below, account name ABC, password for abc123, account level of 15 (highest level) R1#configure Terminal R1 (config) #username ABC privilege secret abc123 R1 (config) #end r1# 2, configure the

are used The route of this packet. ---- GRE only provides encapsulation of data packets. It does not have encryption to prevent network listening and attacks. Therefore, in the actual environment, it often corresponds to an IP address. When the SEC is used together, IPSec provides encryption of user data to provide users with better security. The GRE protocol has two main purposes: internal protocol encapsulation and private address encapsulation. In China, CEN uses almost all TCP/IP protocols,

internal serverThree. Basic configuration:A.R1:Interface ethernet0/0IP address 202.100.1.1 255.255.255.0No shutdownIP Route 0.0.0.0 0.0.0.0 202.100.1.2B.R2:1. Interface configuration:Interface ethernet0/0IP address 202.100.1.2 255.255.255.0No shutdownInterface ETHERNET0/1No IP addressNo shutdown2.DNS Server:IP DNS ServerIP host R4.yuntian.cn 202.100.2.4IP host R1.yuntian.cn 202.100.1.12.PPPOE Server configuration:AAA New-modelAAA Authentication PPP Default LocalUsername

Cisco router Tcl script backdoor 2nd tests Author: Vic The security of Cisco routers is certain. Password verification is required for remote login. The Cisco passwords are encrypted in the following ways:1 not encrypted, plaintext display 650) this. width = 650; "border ="

One. Test the topology:Two. Test ideas:Three. Basic configuration:A.R1:Interface ethernet0/0IP address 202.100.1.1 255.255.255.0No shutdownIP Route 0.0.0.0 0.0.0.0 202.100.1.2B.R2:1. Interface configuration:Interface ethernet0/0IP address 202.100.1.2 255.255.255.0No shutdownInterface ETHERNET0/1No IP addressNo shutdown2.PPPOE Server configuration:AAA New-modelAAA Authentication PPP Default LocalUsername Cisco pass