the above technologies on CISCO switches to address typical Layer 2 attacks and spoofing, to prevent man-in-the-middle attacks, MAC/CAM attacks, DHCP attacks, and address spoofing in the exchange environment, more importantly, address management can be simplified through the deployment of the above technologies, track user IP addresses and corresponding switch ports directly to prevent IP address conflicts
Switch Stack-ports displays full port information for the stack switchStacking common, at present in some financial, logistics enterprises are very common, and the other side of the enterprise is not bad money, as long as the program is reasonable, the budget cost is not very small, so here again to emphasize the professional quality of the network workers have been seasoned pre-sales program capabilities.Think of learning as a living habit.-----------is shared by a network of two-tier operator
Overview of LAN Switches
The LAN switch has developed into a more expansive space from the traditional hub-and-LAN. For example, Cisco's Catalyst 5000 series LAN switch includes an integrated switched hardware architecture that supports switched 10-mbps Ethernet and 100-mbps Fast Ethernet, with Fast Ethernet, FDDI, switched token Ring, and layer 3rd switching capabilities. This class of switches can provid
Q: Are there any simple tools and methods? Run the script automatically on N or so cisco switches according to the script, and then return the result?Method 1: Download and modify the vswitch configuration file and upload it to N vswitches. Restart or copy start run.Method 2: Create a bat file under windows. The content in the file is the same as the command you used to telnet to the vswitch for modificatio
obsoleteAA0001 DEC obsoleteAA0002 DEC obsoleteAA0003 DEC Global physical address for some DEC machinesAA0004 DEC Local logical address for systems running DECNET
2. the preset recovery time of the Cisco switch port is about 30 seconds. That is, unplug the network cable and plug it in. It takes about 30 seconds for the indicator to change from yellow to green. Generally, the switch only t
To prevent IP address theft or employee IP address tampering in a Cisco switch, you can take the following measures: binding an IP address to a MAC address and binding an IP address to a vswitch port.
1. Check the port through IP Address
Check the MAC address first, and then check the port based on the MAC address:
Bangonglou3 # Show ARP | include 208.41 or show Mac-address-table to view the IP-Mac table of the entire port
Internet 10.138.208.41 4 00
Startup Process of cisco routers and switches:
I. cisco switch startup process:
The START loader is a small program stored in NVRAM and executed when the switch is started for the first time.
① The vswitch loads the loader software from NVRAM.
② Start the loader.
③ Perform POST (self-check on startup) for the low-level CPU subsystem ).
④ Initialize the Fl
Today just to restore a Cisco configuration commands, this belongs to my professional small caught dead a back, I hope you forgive!Tools/Materials
Cisco series switching
Method/Step
1First backup of previous configuration informationCopy Flash:config.text Config.old
2Clear Switch Configuration command: Write eraseOf course, you can also use erase startup-config to achieve clear
Ciscolib is an open-source third-party Python module on git that manages Cisco switches. Only simple Telnet management is supported at this time. The management method is very simple, the module source code itself is not complex. It is helpful for daily batch configuration.The module structure is:Official Operating Example:Import ciscolib switch = Ciscolib. Device ("hostname or IP", "Login password", "Optio
When switching data frames, a switch can select different modes to meet network and user needs. Cisco switches provide three switching modes:
Storage forwarding Mode
The Store-and-forward mode means that the switch can complete the entire data frame and perform the forwarding operation only after the CRC verification is passed. If CRC verification fails, that is, the data frame is incorrect, the switch d
Layer-3 Switch for Cisco switches
Although single-arm routing solves the communication problem between different VLANs, it also has its fatal defects:
-The single arm itself is the Backbone link of the network, which is easy to form a network bottleneck.
-The sub-interface relies on physical interfaces, and the application is not flexible
-You need to view the route table for each vlan forwarding, wasting
and security level. Therefore, the network design should prevent abnormal function faults caused by excessive broadcast traffic, and pay attention to the potential security risks. In short, if an exception occurs in the network, the abnormal device will send a large amount of broadcast packet traffic. If too many broadcast datagram traffic occurs within one second, the CPU usage of network devices such as switches is high, and the Set utilization rat
Basic configurations of Cisco switches
One vswitch and two PCs can communicate with each other and allow login to the vswitch terminal.
Command Configuration:
SW1 # vlan database // enter the vlan database
% Warning: It is recommended to configure VLAN from config mode,
As VLAN database mode is being deprecated. Please consult user
Documentation for associating ing VTP/VLAN in config mode.
SW1 (vlan) # vla
Password Recovery for Cisco switches
1. Press and hold the modem key to power on. After Entering the console, release: switch:
2. Load the flash_init file for initialization: switch: flash_init
3. view files in flash: switch: dir flash:
4. rename the configuration file: switch: rename flash: config. text flash: config. old (set at will)
5. Start the vswitch: boot
6. view flash in privileged mode: # di
Password Recovery for Cisco switches
1, hold the modem key, power, to enter the console after release: switch:
2, loading flash_init file initialization: Switch:flash_init
3, view the files in Flash: Switch:dir Flash:
4, rename the configuration file: Switch:rename flash:config.text flash:config.old (optional set)
5. Start switch: Boot
6, in the privileged mode of view Flash: #dir Flash:
7. Change th
Basic configuration and management of switches in Cisco PT simulation experiment, ciscopt
Basic configuration and management of switches in Cisco PT Simulation Experiment
Objective: To understand the basic configurations and management of a vswitch and the basic commands of the vswitch configuration.
Tutorial Backgroun
1. Set host name/system name on iOS based switch:
Switch (config) # hostname hostname
To set the hostname/system name on a CLI-based switch:
Switch (enable) set system name name-string
2. Set the login password on the iOS based switch:
Switch (config) # Enable password Level 1 password
To set the logon password on a CLI-based switch:
Switch (enable) Set password
Switch (enable) Set Enalbepass
3. Set up remote access on iOS-based switches:
Sw
that your server operations are too slow. Check your desktop traffic speed and network switching capability.
Question 4: Maybe tomorrow, the business will double, and the demand for various network applications will double. Are you ready for the network?
Simplifying management and reducing costs are the pursuit of network managers. The network environment is a complex and closely composed environment, and you will find that the network is becoming more and more picky. Remember, the network has
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.