cisco packet sniffer

Use Python to write network packet sniffer (Code a networks packet sniffer in Python for Linux) by Silver Moon Basic SnifferSniffers is programs that can capture/sniff/detect network traffic packet by packet and analyse them for v

ObjectiveLearning Network knowledge of the students have heard or used the network device Simulator, network equipment simulator known to have Huawei's ENSP, Third HCl and Cisco PACKET TRACER, Cisco's simulator with a simple operation interface, Easy to install and use and a variety of easy to work can win a lot of network engineers and students praise. Because I am short-sighted, I will be the most basic l

Tags: cal enhancement packet share image share access Cisco virtual SRCVLAN, the virtual LAN (Virtul local area network), the VLAN divides the physical connected LAN logic into different virtual networks, its existence can reduce the broadcast domain, enhance the network security and convenient and flexible networking, adding PCs and switchesBy configuring VLANs, you can implement PC1 and PC2 that are conne

, adding switches and end devices1, double-click switch into switch command line (CLI) mode, switch configuration mode by command2 in most cases for security reasons, you need to configure the switch privileged mode passwordValidation test3 Configuring the telnet login switchTo achieve remote login, first need to configure the login user and device management addressVerify the configuration by matching the IP address of the PC with the switch management address into the same network segment and

Tags: size src zone sha port text topology Cisc-oTwo networks in different regions if you want to communicate, you need to configure routing on the router to implement the packets across the networkRouters can connect to multiple networks, but the router itself does not know about other networks, and we need to manually configure static routes to let routers know about other network information or to configure dynamic routing to let routers learn about other networks themselves.This learning con

Tags: color-o switch test one-arm routing access via interface implementation representationTo achieve inter-VLAN communication, in addition to configuring the SVI interface on the switch, you can also implement VLAN data forwarding by configuring sub-interfaces under the physical interface of the router.Configuration ideas:1 The access switch configures the corresponding VLAN and sets the access PC port to access mode2 Setting the physical interface of the router to which the switch is connecte

Nat[network address translation] In the absence of IP address in the case of a great use, it can not be normal Sisu network of the intranet address into a legitimate external network address on the public network to send and receive data. At the same time address translation function can also be very good to hide and protect the host network.Nat has static NAT (internal address and external address one-to-one) and dynamic NAT (internal address pool and external address Pool A-do)This time we'll

Network address port Conversion NAPT is a very familiar way of transformation. NAPT is commonly used in access devices, which can hide small and medium-sized networks behind a legitimate IP address.Unlike dynamic address NAT, NAPT maps An internal connection to a separate IP address in the external network, adding a TCP port number selected by the NAT device to the address.This time, let's get to know napt.Configuration ideas1 Configure the router's interface IP address, note the network segment

RIP protocols can be configured in a more convenient way, but the limitations of RIP itself indicate that it is not suitable for medium to large networks. In contrast, OSPF is more complex to configure than RIP, but its functionality and performance are better than RIP.Configuration ideas1 Configure the physical interface address of the router Xia Lian switch and the physical interface address of the router to the other router and open the port2 Configure the address of the switch Xia Lian PC an

Through the previous experiment we learned that by configuring VLANs, the terminals under different VLANs could not communicate with each other, but if you wanted to communicate between different VLANs, you would need to configure inter-VLAN routingLayer three switches have the capability of the network layer and can be forwarded via the routing functionNetwork environment1 set the IP address and gateway of the terminal (192.168.1.1 and 192.168.2.1, respectively).2 VLAN is configured under Layer

Tags: process proc ima RAC Technology share static term ADOBy configuring static routes, you can achieve an increase in routing entries for routers in a relatively simple network.However, if there are more than 20 routers in a network, it is difficult to configure static routes to accommodate the complexity of routing entries and changes in the network. At this point we can use the RIP protocol to configure simple dynamic routing, thus reducing the workload.Configuration ideas1 Configure the IP

policy in Router 2, specifying host and port7 The ACL takes effect under the port of the Router 2 Xia Lian serverNetwork topology1 Configuring Router 1 single-arm routing, establishing sub-interfaces and configuring IP addresses, etc.2 Configuring the Switch's VLAN and port type3 Configuring the IP address of the PC4 Configuring the interface address for Router 25 Configure static routes to communicate properly between networks6 Configure the ACL policy on Router 2 to allow PC1 to access the se

port to enable ACL policyNetwork topology1, configure Router 1, turn on the single-arm routing configuration subinterface address and connect the physical interface address of another route and open the port2 Configuring the VLAN of the switch, configuring the port type3 Configuring the IP address of the PC, specifying the gateway4 Configuring router static routing to enable network interoperability5 Create a new ACL policy on the destination router6 Enter the destination port to make the new A

Tags: tle simulates a trunk mode ace 51cto fast spanning tree quick typeLoops are present in the network, and all loops are formed due to confusion caused by ambiguous destination paths. The loop has a great impact on the network. Spanning Tree protocol is a good solution to this problem.The idea of spanning a tree protocol topology is that, regardless of the physical connection between switches, the switch can automatically discover a network with no loop topology, and the network of the logica

Install Cisco Packet Tracer in Linux What is Cisco Packet tracer? Cisco Packet Tracer is a powerful network simulation tool used for Cisco authentication training. It provides us with

What is Cisco Packet tracer?The Cisco Packet Tracer is a powerful network simulation tool for training in Cisco certifications. It gives us a good view of the interfaces of each router and network device, with many options, and we can use unlimited devices in the network jus

Lab Environment:650) this.width=650; Tracer of "alt=" Cisco Packet EtherChannel increases link bandwidth and redundancy-Ibm.chick-mingkang.zhou "src=" http://img0.ph. 126.net/1inyhgrqquafdjfzpjjgsw==/6630808280955124494.jpg "style=" border:0px;height:auto;margin:0px 10px 0px 0px; "/ >Experimental Purpose:1. Observe the STP status of the two switches.2. Configure the EtherChannel, and add the physical port t

This article mainly uses an example to explain in detail how to solve the packet loss problem caused by CISCO router faults? The following article gives me a detailed answer. Recently, some people in my department (Department A) reported that they could not access the network of the higher-level department (Department B. I use the ping command from the computer A1 (IP Address: 10.20.12.11/24) used by this p

Cisco ios xr bgp Packet Processing Denial of Service Vulnerability Release date: 2010-08-30Updated on: 2010-08-31 Affected Systems:Cisco ios xr 3.4.0-3.9.1Description:--------------------------------------------------------------------------------Cve id: CVE-2010-3035 Cisco ios xr is an operating system with self-protection and self-repair functions used in

Cisco held a network lecture entitled "define your router with 256 or fewer bytes". The subject of this lecture is: "the accuracy and performance improvement of network security products forces hackers to successfully launch attacks in the first 256 bytes of the Code, so that they can easily intrude into the network without being noticed ". As a result, Cisco developed a technology named Flexible