Read about cisco press ccnp switch, The latest news, videos, and discussion topics about cisco press ccnp switch from alibabacloud.com
[Experimental environment] veryhuo.com C3640-IK9O3S-M Version 12.4 (10) veryhuo.com [Tutorial Objective] Lie's Fire Network The tunnel technology is used to expand the frame relay switch simulated by the router to make up for the insufficient frame relay interface caused by limited router interfaces. Lie-fire-network [Experiment topology] Liehuo.net Veryhuo.com [Experiment description] liehuo.net In the experimental environment, because frame relay
the switch is started, press Enter to get a user prompt. Press Enter for the following time: After a vswitch is enabled, the following message is displayed: Cisco switch password recovery Cisco
Cisco switch iOS upgrade, actually quite simple, but need to note is, can not let the switch flash storage is empty, must have an iOS in, or no iOS in Flash, waiting to upload iOS with Xmodem, so your time can be a lot of waste ah. Because the Rommon mode is not available for the Cisco Catalyst 2950, 2960, 3550
It is also helpful to understand some of the knowledge about switch configuration, and here we explain the main statements and procedures for Cisco switch configuration. Last talk with you about how to properly connect the switch, today with some configuration clips to introduce the port configuration. Given that most
current configuration information (Information in RAM) 51cto # show startup-config \ view the information of the saved disk (Information in NVRAM) 51cto # show ip route \ view route table information 51cto # show cdp neighbors \ check which cisco devices are connected to this vro 51cto # erase startup-config \ recover the vro to the factory configure 51cto # reload \ restart vro password recovery 1 start up press
Company a device, Ws-c2960s-24ts-l, is the Cisco 24 Port 1000M Two layer Exchange Yang, the use of iOS version of 12.2 (UNIVERSALK9-M) iOS software, the company recently installed some digital cameras, The monitoring host and a billiard-type monitoring to the machine, the interface of the transmission rate is much larger than the rate of ordinary office, the following is the rate of the two interfaces I copied.G1/0/3 (Monitoring host interface)5 minut
The detailed steps for restoring the password of a Cisco switch are illustrated. If the password of a Cisco switch is improperly restored, the password will be lost. Today, we will contact the steps for restoring the password of a Cisco
Recently, the OS of a vswitch is old, so I want to update it. I want to ask a user to update the OS. After updating the OS, the problem occurs, I have a password for the OS. Since the password is being used and it is difficult for them to ask for it, I am ready to clear the password. After finding the relevant article on www.cisco.com, cleared successfully. Write down the cleanup process. Let's talk about the configuration environment first, the switch
#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--
password to enter the privileged mode, and the original configuration content is retained.Operation steps: 1. Prepare the console cable and connect the Super Terminal. 2. Restart the switch (because 2950 does not have a power switch, you can directly unplug the power cord and connect it back.) 3. Press the MODE key at the start to enter the
With the development of China's routing industry, we have also promoted the update and upgrade of the routing switch technology. Here we have introduced the IOS restoration method of the Cisco routing switch, and we have tried one method, after Flash is deleted, the system cannot be started. You can use X-Modem to restore it. At that time, I accidentally deleted
1. Unplug the power cord of the vswitch, press the switch Mode button, and re-plug the power cord of the vswitch. Release the Mode button after the LEDs on Port 1x are off. 2. For the Catalyst 2940/2950 L series: Unplug the power cord of the switch, hold down the Mode button of the switch, and re-plug the power cord of
Cisco switch password settings www.2cto.com 1. set console password> enable # configure trminal (confing) # line console 0 secure console port ① (config-line) # password (cisco) Secure password (config-line) # login logs must not be small. console Password settings complete exit 2: set the global password www.2cto.com enadle # configure terminal ② (config) # enab
Cisco switch status lights are all available on the front panel of the Cisco switch and are used to monitor system activity and performance. These LEDs are called LEDs ).The indicators on the front panel include: · system indicator www.2cto.com · remote power supply indicator · port mode indicator · Port Status Indicat
Tags: cisco switch password resetCisco switch, what do we do when we forget its login password? How do I clear its password? principle: Enter the bottom of the switch, by modifying the switch original profile name, after restarting the s
Cisco 2960 Switch Configuration1. Cisco Working mode classification and function#用户模式仅答应基本的监测命令, the configuration of the router cannot be changed in this mode.Switch> #用户模式#允许用户执行所有的测试, view, save and other commands, this mode can not be modified router configuration, generally this mode is recommended to set password protection.Switch>enable #进入特权模式
and a switch are connected with the console lineHow it works: Switch password recovery fundamentals: Change the Config.text file name in the switch to a different file name, and then enter the configuration mode to change the password, and finally restore the Config.text file nameSteps:1. Power off first2. Power off while holding down the mode key on the
Cisco switch recover master diskRecovering from a Software Failure1. download the system image from the cisco website. The cco account is required. unzip the system image, decompress the unzipping is binary executable binfile Unix using tar-tvf command unzip unix-1 % tar-tvf image_filename.tarunix-1 % ls-l image_filename.bin3. select 96004 at the speed of the con
Ciscoswitch password reset steps1.PCMachine has Breakmethod of the key1.1Interrupt Device startup Ctrl+break keyStep: Turn off the device and restart:Self decompressing the image: Press the Ctrl+break key when you start the device ##########################Monitor:command "Boot" aborted due to user interrupt1.2change the value of the configuration register to 0x2142(Two register values:0x2102 (Normal),0x2142 (do not read the saved configuration))s
Lab Environment:The company has a Cisco switch that forgets the login password and cannot enter into privileged mode.Implementation features:To modify the login password in privileged mode1, desktop----start----All Programs----attachments----hyperterminal----files----New Connection---CustomThe name test----OK.2. The COM1 (depending on the actual situation) used in the connection is----determined.3, Rate: 96
Start building with 50+ products and up to 12 months usage for Elastic Compute Service
1 on 1 presale consultation
24/7 Technical Support 6 Free Tickets per Quarter Faster Response
Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.
A comprehensive suite of global cloud computing services to power your business
Payment Methods We Support
