cisco rip configuration

For complete syntax and application information about this chapter, seeCatalyst 3550 Multilayer Switch Command ReferenceAnd Cisco IOS Interface Command Reference For Release 12.1. Understanding Interface Types This section describes different interface types and some reference content for configuring these interfaces in detail in other sections. Other sections describe the configuration process of physi

Cisco ASA L2TP over IPSEC configuration details 1. Create a VPN address pool Ciscoasa (config) # ip local pool vpnpool 192.168.151.11-192.168.151.15 mask 255.255.255.0 2. Configure the Ipsec encryption algorithms 3DES and SHA. Ciscoasa (config) # crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des (esp-sha-hmac) 3. Set the IPSec transmission mode to transport. The default mode is tunnel (L2TP only suppor

1. Cisco DHCP configuration ideas In global Mode Ip dhcp xxxx name DHCP address pool XXX, only for marking Network allocation address and subnet mask Default-router assigns a gateway DNS-the server allocates DNS, which can be separated by spaces. ..... Exit In global Mode Ip dhcp ex start address end address allocation reserved address is not used for DHCP, such as gateway 2. Multi-vlan dhcp h

Cisco 2811 Routers Detailed configurationRouter>enableRouter#configure TerminalRouter (config) #hostname cisco2811//define router name2811 (config) #enable password 124563831//Set Login password2811 (config) #line vty 0 42811 (config-line) #password 124563831//Set Telnet password2811 (Config-line) #login2811 (Config-line) #exit2811 (config) #interface fastethernet 0/0//Set Intranet interface2811 (config-if) #ip address 192.168.1.254 255.255.255.02811

Encapsulation dot1q2 Configuring the Port as TrunkJ2 (config-if-range) #switchport mode trunkTo add VLANs on the trunk:J2 (config-if-range) #switchport trunk allowed VLAN add 50J2 (config-if-range) #switchport trunk allowed VLAN add 60To remove a VLAN from a trunk:J2 (config-if-range) #switchport trunk allowed VLAN Remove 50To view the interface mode:j2#sh int F1/1 SwitchportName:fa1/1Switchport:enabledAdministrative Mode:trunkOperational Mode:trunkAdministrative Trunking encapsulation:dot1qOpe

Lab Environment:1. Configure two VLAN 10 and VLAN 20VLAN IP address settings: 192.168.10.1 255.255.255.0 (192.168.10.1 is a VLAN 10 gateway address)VLAN IP Address setting: 192.168.20.1 255.255.255.0 (192.168.20.1 is a VLAN 20 gateway address)2. (Windows Server R2 operating system) set up a DHCP server to create two scopes VLAN 10 and VLAN 20,Get the IP address dynamically using VLAN 10 and VLAN 20. The DHCP server NIC accesses the switch FA0/1 port.DHCP server network card settings:ip:192.168.1

Cisco router configuration mode In general, you can configure your router in 5 ways: 1.Console Port connection terminal or running terminal simulation software of the microcomputer; 2.AUX Port Connect modem, connect with remote terminal or computer running terminal simulation software by telephone line; 3. Via the TFTP server on the Ethernet; 4. Adoption of the Telnet procedure on the Ethernet; 5. Thr

I. Overview: Cisco 15.2 iOS support IKEV2 IPSec VPN, security is more IKEV1, the first phase of authentication methods also have a variety of ways to support the local and remote use of different authentication methods, this test for both sides both local and remote use of preshared key method. Two. Basic ideas: The A.VPN peer is configured with a static VTI mode while the dynamic VTI mode is used. B. The actual test found that the VTi interface c

The port Mapping method enables access to specific port services from the Internet to the local area network internal machines. For example, the machine you are using is in a LAN connected to the Internet, all the services you open on the machine (such as FTP), by default, the outside world can not access. This is because your IP is the LAN internal IP, and the outside can access only the server you are connected to the IP, because the entire LAN on the Internet only a real IP address, and this

5 , configuring the routing capability of the switchNote: Routing is only available on a three-layer switch, and other two-tier access switches are not allowed to transfer data between different VLANs until the routing is switched through the trunk port to the core switch .TEST (config) #ip Routing # enables the routing function of the three layer switch, which is turned off by defaultTEST (config) #ip Route 0.0.0.0 0.0.0.0 172.16.0.1# Configure the default route for the switch, which is the tot

There are many VPN products on the Cisco ASA Web VPN configuration market and their technologies are different. For example, in the traditional IPSec VPN, SSL allows the company to achieve more remote users to access the VPN in different locations, this service enables more network resources to be accessed and has low requirements on client devices, reducing the configu