You may be familiar with the RIP Protocol. This Protocol is widely used. This Protocol is applied in many networks. If you do not have RIP configuration, you don't have to worry about it. Next we will explain the configuration process in detail, so that everyone can learn it.
IP Address
1. There are three routers in the following network, and all routers run the RIP Protocol. Only three routers need to communicate with each other.
Configuration:
Joe(config)#routerripJoe(config-router-rip)#network192.168.0.0/24Joe(config-router-rip)#network192.168.1.0/24Hamer (config) # rout
The diagram above is a configuration topology diagram
R1,R2,R3,R4 all RIPv2 get the route, the following is the configuration document.
System {root-authentication {Encrypted-password "$1$pc0igedw$xh19u99vsa6azotdk9bfz."; # Secret-data} logi
n {User Mengmeng {UID 2001;
Class Super-user; Authentication {Encrypted-password "$1$keim0kf/$ezlHwRupnb 7HFdUZVdIvE."; # # Secret-data}}} Services
{telnet;
Packet Tracer 5.0 Experiment (ix) router RIP dynamic routing configurationFirst, the experimental target
Master the configuration method of RIP protocol;
Master to view the routes generated by RIP learning through dynamic routing protocols;
Familiar with the connection mode of WAN cable;
Second, t
I. Lab Objectives
Master the configuration of the RIP Protocol;
View the Routes learned through the dynamic routing protocol rip;
Familiar with Wan cable connection methods;
Ii. Lab background
Assume that the campus network is connected to the egress router of the campus network through a layer-3 switch, and the router is connected to another router outside
Configuration of the RIP route protocolRIP (Routing Information Protocol) is one of the most commonly used internal gateway protocols. It is a typical dynamic Routing Protocol based on D-V algorithm. User datateprotocol (UDP) packets are used to exchange route information, and the number of hops (Routing cost) is used to measure the distance to the destination ). Because the number of hops larger than or eq
"Experiment name"RIP routing Protocol basic Configuration. "Experimental Purpose"Master How to configure on the router RIP routing protocol. "Background description"Assuming that the campus network is geographically divided into 2 regions, each of which has a router connected to 2 subnets, two routers need to be connected together via an Ethernet link and configu
"Experiment name"RIP routing Protocol basic Configuration. "Experimental Purpose"Master How to configure on the router RIP routing protocol. "Background description" assume that the campus network is geographically divided into 2 2 subnets, you need to connect two routers over an Ethernet link and configure it appropriately to achieve this 4 Span style= "font-f
address rollup Configuration instance, the topology diagram looks like this: R2 connected to multiple network segment address (especially this kind of continuous IP address is the most should do network summary), the same R4 also configured a lot of network segment information. r2 r1 " between OSPF protocol area1 area, r1 and R3 area0 backbone area, r3 and R4 rip The loopback 0 address
RIP Theory SectionHow RIP routing protocols work:v Regular Updates (periodicupdates): Updates are sent each time a specific period of the cycle is passed. Neighbor (neighbors): A router that shares the same data. v Broadcast Update (broadcastupdate): When the router is first activated, it uses the simplest method to send update information to the broadcast address. v fullRoutingtable update: broadcasts its
Cisco configuration instance _ Cisco dual-Egress NAT configuration objective: to simulate the routing function based on the original address policy when a dual-Egress link is available, and access to the external network from different original addresses is realized, in most cases, the vro uses NAT to translate the Int
RIP configurationThe Rip[process-id] command is used to enable the RIP process. In this command, Process-id specifies the RIP process ID. If Process-id is not specified, the command uses 1 as the default process ID. VERSIONNBSP;2 enables RIPV2 to support extended capabilities, such as supporting VLSM, certification, an
Topology diagram:Requirements:Understand the operation principle of RIP protocol, and realize different network interworking through RIP routing protocol.Configuration steps:1, configure the PC IP address and other parameters. PC 0>ipconfig IP Address ....: 10.1.1.2 Subnet Mask ...: 255.255.255.0 Default, ......, ...................... The Gateway ...: 10.1.1.1... ......2. Configure IP address parameters fo
can give the basic configuration command for a Cisco Route (preferably with a Chinese explanation ),
Summary of Cisco Route configuration statementsStart the interface and assign an IP Address:Router>Router> enableRouter #Router # configure terminalRouter (config )#Router (config) # interface Type PortRouter (config-i
Experimental purposeMastering how RIP routing protocols are configured on routersDemand analysisTwo routers are connected by a fast Ethernet port, two loopback ports are set up on each router, the RIP routing protocol is run on all ports, and interoperability between all subnets is realized.Principle of experimentRIP is a typical distance vector protocol for small homogeneous networks, which is an early app
Detailed configuration process of dynamic route protocol RIP (1)
This blog post is from Bkjia blog bvbvbvbv07. If you have any questions, go to the blog page for an interactive discussion!
Blog: http://zhang2015.blog.51cto.com/9735109/1618123
First, set up the IP address of the topology planning and find out what needs to be configured and the lab requirements ......
Packet Tracer6.0 Static Routing, rip routing, ospf routing configuration, tracer6.0ospf
OSPF Dynamic Route configuration Scheme
First, we cleared the RIP configuration information configured in the router in the previous article. R1.R2. R3 cleared the
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.