Alibabacloud.com offers a wide variety of articles about cisco router and switch simulator, easily find your cisco router and switch simulator information here online.
Cisco router VLan isolation LAN broadcast packet configuration experiment and summary, ciscovlan
1. Tutorial Description: connect to and set the IP address of the PC according to the network topology. PC1 and PC2 are required to be accessed on VLAN 12, while PC3 and PC4 are accessed on VLAN 34, PC1 and PC2 are interconnected, PC3 and PC4 are interconnected, and VLan 12 and VLan 34 are interconnected to isol
interruptRommon 1 > "Interrupt"2.2go in Rommon mode start using the command configuration as follows Step:Rommon 1 > Confreg Choose y or N below the word bad I'll tell Y or N in the order of choice. Excuse me. The order is as follows: 1. Y 2.N 3.N 4.N 5.N 6.N 7.Y 8.N 9.N 10.N650) this.width=650; "style=" Float:none; "title=" 123.png "src=" http://s3.51cto.com/wyfs02/M02/71/37/ Wkiom1xjr8dtoehaaagcy3dy9aw290.jpg "alt=" Wkiom1xjr8dtoehaaagcy3dy9aw290.jpg "/>650) this.width=650; "style=" Float:non
Vswitch Virtual Network (Virtual LANs) settings:VLAN division and external VLAN routing settings on Catalyst 5000Assign a VTP Domain)Add Cat5000 to the domainSpecify the relay port (a Trunk)Dynamic ISLAllocate VLAN to PortSet VLAN 20Configure the RouterNote: There are three VLANs, which are routed between VLANs through the Router.-Allocate VTP DomainsWhat is VTP?VTP is short for VLAN Trunk Protocol. It provides each device (
================================ The port role is the specified interface, but the status is discarded, no forwarding is provided.
It turns out to be an rstp problem.
Why is a specified interface discarded? The specified interface should be fowding.
Suddenly, a friend prompts me that if the rstp interface is selected as the specified interface, the downstream confirmation is required to enter the forwarding status.
The P/A mechanism requires the link between the two switches to be point-to-poin
asked the boss, and he did not know it. It is said that the password was changed by the supplier. So the phone supplier asked the password for a long time and got a reply: at that time, the changed employee quit, and now he does not know the password .... dizzy .. too irresponsible .. there is no way to ask for your own, for your own, for google... (Although I have learned how to restore the password of a Cisco r
Cisco router nat translation 1. One-to-one correspondence between the internal address and the egress address disadvantages: When the egress address resources are scarce, only a small number of hosts can be connected to the internet. 2. The internal address shares the egress address. The router uses the egress address and port number, as well as the external host
There are too many Qos information on the Cisco Router Traffic Control instance, but many of them are not practical. I have talked about a lot of theories. The following are the configurations on the routers of a subsidiary for your reference. In fact, as long as you understand the meaning of NBAR, CBWFQ, and WRED, traffic control can be configured as needed. Www.2cto.com Description: A subsidiary uses a 2
As we all know, Cisco device iOSUpgradeIs simple, just set up an FTP or TFTP server and use it on a Cisco deviceCopy tftp: (or ftp:) Flash: (The high-end device is generally sup-bootdisk:)You can do it. And after the upgrade of the high-end device fails, even if you delete the original iOS, you just need to get a flash card, the iOS directly to the flash card, and then plug into the engine with the Flash ca
Router and three-layer switch experiment Demo--a gateway that acts as a two VLAN--Hundred dishes background : We know that routers have routing capabilities, so you know how to configure two gateways on a router interface (such as a two VLAN gateway)? Note that it is on one interface instead of two, and we sometimes use the three-layer
Hardware and Software Versions
This configuration is applicable to all Cisco IOS software versions.
DCE edge is connected by Wan DCE cable.
DTE edge is connected by Wan DTE cable.
For more information about the wan dce/DTE cable, see the serial cable documentation.Network Diagram
650) this. width = 650; "src =" 51cto.com/uploads/allianz 110909/1212454314-0.jpg "border =" 0 "/>
This article is based on the following Configuration:
In this configuratio
by the manufacturer. because the latter is a design value, the test is very difficult and the significance is not great. (This sentence seems to be reversed)
The switch's back-board speed is generally Mbps, which refers to the second layer,
Mpps is used for switching between three or more layers.
Wireless Router password cracking
The utilization rate of the backboard Bandwidth Resources is closely related to the internal structure of the vswitch. Cur
Branch switches.The Cisco switch can support any media as a trunk line. To achieve relay, you can use its unique isl tag. Isl (inter-switch link) is a protocol for transmitting vlan information and vlan data streams between switches, between switches and routers, and between switches and servers, by configuring isl encapsulation on the port directly connected to
Tags: Cisco switchBasic configuration and management of switches• Technical Principles• The switch is managed in two basic ways: in-band management and out-of-band management.• The console port management switch through the switch is out-of-band management, which does not occupy the network port of the
Whether it's on a Cisco router or a network device such as a Cisco switch, the standard ACL access control list is always unable to match both the traffic source address and the destination address, nor does it meet the requirements of the "granular" control of the current network world, such as: A service function tha
Application (ACL) of the access control list of cisco router Integrated Experiment ii ip Address Configuration on each device, steps ======================================================== ========================================================== ======================================= Configure route R1: (config) # ip route 0.0.0.0 0.0.0.0 192.168.1.254 route www.2cto.com R2: (config) # ip route 0.0.0.0
Configuration of a layer-3 Cisco switch 1. Start a route on a layer-3 switch. Otherwise, layer-3 switch does not have the routing function switch (config) # ip routing2. Configure the VLAN ip address switch (config) # interface vl
to say, after you set the password for level 1, you will be asked to enter the password next time you connect to the switch and enter K, this password is the password set for level 1. Level 15 is the privileged mode password that you enter after you enter the enable command.
Step 2: Set the VLAN name. Because the four VLANs belong to different switches, the command for VLAN naming is VLAN 'vlan No. 'name' vlan name ', the following code configures VL
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.