Alibabacloud.com offers a wide variety of articles about cisco router configuration, easily find your cisco router configuration information here online.
Product introduction
Cisco SDM is an intuitive and web-based device management tool for managing routers based on Cisco ios® software. Cisco SDM simplifies the router and security configuration process through the Smart Wizard, and with these wizards for customers and
Test environment:
Cisco Router Intranet interface F0/1:192.168.1.1 255.255.255.0
External network Interface f0/0:10.0.0.1 255.255.255.0
Server ip:192.168.1.100
First configure on the router:
Router>en #进入特权模式
router#conf T #进入全局配置模式
Enter
RIP and IGRP are commonly used router configuration protocols. What problems should we pay attention to when configuring RIP and IGRP? What should we do? The following configuration steps provide detailed answers.
RIP Protocol
RIP (Routing information Protocol) is an Internal Gateway Protocol (IGP) that is widely used earlier and is suitable for small-sized sim
In Cisco router configurations, NAT configurations are frequently used. I hope the introduction below will be helpful to the majority of fans. It is a common method. The vro performs simple NAT translation and sets a CIDR Block in the NAT address pool. After a while, I found that the address pool was a waste of time. When I wanted to use a real ip address, I couldn't use it, so I decided to modify the
Cisco router configuration manual Virtual LAN (VLAN) routing 1. The main network technology we currently use when constructing an enterprise network is generally based on exchange and virtual networks. The exchange technology changes shared media to exclusive media, greatly improving the network speed. The Virtual Network Technology breaks the restrictions of the
address of the TFTP server be entered. After the Server IP address is correctly entered, the router also requires the network administrator to provide the configuration file name to be backed up. Generally, we recommend that you use a file name that is easily remembered by the Administrator. At this time, the router will prompt the Administrator to press YES to
Tags: erase cmd terminal copy Cisco forgot password direct out settingLab tasks:1. Configure the password in Cisco mode routing2. How to reset the password after forgetting the passwordExperimental steps:1. Give Router a password:Router >enable#config TRouter (config) #line vty 0 4//Incoming Remote management interface#password//123 Configure password 123Exit
encapsulation method used by the serial port or ISDN InterfaceEncapsulation sap specifies that the Ethernet 802.2 format Cisco password used on the network segment is SAPEnd exit Configuration ModeErase deletes flash memory or configures CacheErase startup-config Delete content in NVRAMExec-Timeout: specifies the time that the exec command interpreter has waited before user input.Exit to exit all
unique.
Default route Configuration
The default route is generally used in the stub network, and the stub network is a network with only one egress path. Use the default route to send packets that are not included in the route table of the target network. In fact, you can understand the default route as a static route with a wildcard (wildcard.
Dynamic Routing Protocol configuration method:
IGRP dynamic Pr
In addition to address binding, ARP configurations of Cisco routers are getting more and more attention. Therefore, we will discuss two aspects here. It seems a bit messy, but I hope it will help you. I know that the command for binding the IP address of the cisco router to the mac address is arp IP address, mac address, arpa, but I think there should be a comman
Dhcp configuration commands for Cisco router R1 (server) -------------------- R2 (client) www.2cto.com dhcp configuration of Cisco router and their explanations are as follows: r1dhcp service
This article uses VPN technology to achieve interconnection between two parts of the network, simulate ISP, close to practicality, the article mainly shows us the specific operation steps, mainly the input of basic commands.
In this experiment, we use the Cisco 2600 router and VPN technology to achieve the network interconnection between one branch and two parts. To stay close to practicality, we still use
Configure the PPPoE configuration for connecting a CISCO router to an ADSLmodem through the PPPoE configuration: hostnamebjsite! Ipsubnet-zeronoipdomain-lookup! Vpdnenablenovpdnlogging! Vpdn-group1request-dialinprotocolpppoe! Interfaceethernet00ipaddh
Configure PPPoE for connecting a
China Mobile's GPRS network uses the APN method to connect to the GPRS device terminal and communicate with the server through the APN. The customer purchased the Cisco 2811 router, and the mobile company needed to pull the optical fiber through the E1 port, I spent more than 1000 RMB with an E1 module. mobile companies are doing very poorly, and optical fiber connectors are not provided at all. I also boug
NAT configuration on a CISCO router is in full swing and causes the shortage of IP addresses. to alleviate this problem, an important application is NAT (Network Address Translation ), it is widely used. Through address translation, NAT enables enterprises to access the Internet by using only a small number of valid IP addresses on the internet, effectively allev
Configure PPPoE for connecting a CISCO router to an ADSL modem using the Cisco router: hostname bjsite! Ip subnet-zero no ip domain-lookup! Vpdn enable no vpdn logging! Vpdn-group 1 request-dialin protocol pppoe! Interface Ethernet0/0 ip address 192.168.0.1 255.255.255.0 ip nat inside no ip mroute-cache!!!! Interface E
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.