Configuration example of cisco router and layer-3 Switch environment, cisco layer-3 SwitchSimple environment configuration instance for cisco router layer-3 Switch
I. network topology:
Basic configurations of Cisco routers and switches: www.2cto.com Router> \ enter the user mode Router when the vro is started> enable \ type the command to enter the Router mode # \ This display mode indicates that the Router mode has been entered # configure terminal \ type
Encapsulation Frame-relay boot Frame Relay Package
Encapsulation Novell-ether rules the Novell unique format used on the network segment
Encapsulation PPP set PPP to the encapsulation method used by the serial port or ISDN interface
Encapsulation SAP rules the Ethernet 802.2 format used on the network segment the Cisco password is SAP
End Exit Configuration mode
Erase Remove flash memory or configure cache
Erase Startup-config Delete the conte
and a switch are connected with the console lineHow it works: Switch password recovery fundamentals: Change the Config.text file name in the switch to a different file name, and then enter the configuration mode to change the password, and finally restore the Config.text file nameSteps:1. Power off first2. Power off while holding down the mode key on the
CISCO router device categoryThe name rules of cisco routers start with cisco, such as cisco2611 and cisco2610. cisco is the name of the device manufacturer, 26xx represents the 2600 series routers, and xx is a more detailed classification. The following lists several common
Topology map:
1. Configure the router R4 as a Frame relay switch
Frame-relay switching * configured as Frame Relay switch
2. Configure the interface's clock frequency, package type, LMI type and Frame Relay DCE on the router R4
int s0/0
No shut
Clock rate 64000 * Set clock frequency
Encapsulation Frame-rel
When configuring the Cisco 3560 switch in the morning with the Cisco Packet Tracer practice, it is found that the IP address of the port cannot be configured in port configuration mode.Switch>Switch>enableSwitch#configure TerminalSwitch (config) #interface F0/1Switch (config-if) #?DhcpOnly DHCP commands are available.
Use a cisco router to simulate how to configure a frame relay switch (configure 3640 as a frame relay switch): 3640 (config) # frame-relay switching ---------------------- enable the frame relay switching function of the router 3640 (config) # int s0/0 ----------------------
The Cisco router switch sets automatic backup for IOS files and restores the automatic backup and rollback of Cisco IOS configuration files. The archive configuration mode function of IOS is required. Generally, only IOS versions 12.3 (4) All commands for automatic backup of the Ci
When I got up this morning to go to the forum, I saw a post. Ask how to solve the following problem?
A Cisco three-tier switch divides 3 VLANsVLAN 2:IP 192.168.1.1 255.255.255.0 192.168.1.254 Network SegmentVLAN 3:IP 192.168.2.1 255.255.255.0 192.168.2.254VLAN 4 IP 192.168.3.1 255.255.255.0 192.168.3.254Each VLAN can communicate with each other.Now add 1 Cisco r
Simply record that a Cisco router is simulated as a frame relay switch, and the router must have a serial interface module. Liehuo.net
// Enable Frame Relay switching on the vroFRSW (config) # frame-relay switching strong-fire-network
// Enter the Interface Configuration ModeFRSW (config) # int serial 0/1
Veryhuo.co
successfully and you can view your saved files on the TFTP server.4. Restore your configuration file, ping the TFTP server, keep the connection, download from TFTP to the routerCopy tftp running-config Download the previously configured backup from TFTP and restore the router's configuration fileIP address of the 192.168.1.1 TFTP serverRUNNING-CONFIG-BK you want to restore the backed up files in TFTPRunning-config a name for your recovered files.Final reload, successful restart, successful reco
When we want to perform permission rating management on a Cisco router or switch, it is often necessary to assign different levels of users a command that exceeds the default settings, such as show run, which is the most basic troubleshooting command.However, the command cannot be executed when your user level is at 0-14. You can assign permissions to these users
Cisco is now the world's largest manufacturer of switching routes! Many of our businesses, large and small, can use the network, and it is possible to switch routes to Cisco! When we install network equipment, we may ask the network engineer to help us install it! Access to the router has a lot of passwords! What if we
There are multiple backup technologies for Cisco routers. Here we will introduce the router's own backup technology and line backup technology.
Generally, a router is a bridge between a LAN and a wan.
The so-called router's own backup technology is designed to solve a router's own hardware (such as memory, CPU) or software IOS fault or local port fault, network breakdown caused by the failure of the port o
An instance of VLAN configuration for Cisco L3 switches and L2 SwitchesCisco VLAN implementation is usually port-centric. The port connected to the node determines the VLAN in which it resides. There are two ways to allocate a port to a VLAN: Static and Dynamic. The process of creating a static VLAN is to forcibly allocate the port to a VLAN. That is, we first create a VLAN on The VTP (VLAN Trunking Protocol) server, and then assign each port to the c
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.