cisco router throughput

First, the experimental topologySecond, the specific configurationRouter (config) #do sh runbuilding configuration ... Current configuration:604 bytes!version 12.4no service Timestamps log datetime MSECNO service timestamps debug datetime MSECNO Service Password-encryption!hostname router!ip dhcp excluded-address 192.168.1.1!IP DHCP Pool ABCNetwork 192.168.1.0 255.255.255.0Default-router 192.168.1.1Dns-serv

that needs to be mapped to the Internet for access by others. 650) this. width = 650; "border =" 0 "alt =" "src =" http://www.bkjia.com/uploads/allimg/131227/02223S615-0.jpg "/> The specific requirements are as follows:1. Only Internet users are allowed to ping the server and log on to the server through SSH;2. Only Intranet users are allowed to ping the server and log on to the server through telnet;3. Intranet users can access the Internet freely;4. The server cannot access the Internet.Step

Cisco router reset enable password tutorial, ciscoenable Steps: 1. Restart the vro and press ctrl + Breack when ROM Monitor mode appears on the vro to enter ROM mode, for example: 2. Modify the vro register value, change the original register value 0x2102 to 0x2124, and then run the reset command to restart the device, for example: 3. After the password is changed, the value of the drop register in

In this experiment, the speed limiting device of a Cisco router is completed by a Cisco2811 router. In this experiment, we will first look at the flash: www.2cto.com yourname # dirDirectory of flash on the router in two ways: /1-rw-25438028 Oct 22 2010 02:25:58 + 02:26:08 c2800nm-ipbase-mz.124-15.T.bin2-rw-1505280 Oct

, dynamic address translation, and multiplexing dynamic address translation. The following example uses a Cisco router.1. Static address translationStatic address translation performs one-to-one conversion between the internal local address and the internal legal address, and specifies the legal address to which the conversion is required. If there are WWW servers or FTP servers in the internal network that

that needs to be mapped to the Internet for access by others. The specific requirements are as follows:1. Only Internet users are allowed to ping the server and log on to the server through SSH;2. Only Intranet users are allowed to ping the server and log on to the server through telnet;3. Intranet users can access the Internet freely;4. The server cannot access the Internet.Step 1:First First, ensure that the server and PC can ping the gateway GW, then perform NAT on the GW, and ensure that t

When configuring the Cisco 3560 switch in the morning with the Cisco Packet Tracer practice, it is found that the IP address of the port cannot be configured in port configuration mode.Switch>Switch>enableSwitch#configure TerminalSwitch (config) #interface F0/1Switch (config-if) #?DhcpOnly DHCP commands are available. Check on the Internet, the original switch port is Switchport, that is, the two-layer swit

When we want to perform permission rating management on a Cisco router or switch, it is often necessary to assign different levels of users a command that exceeds the default settings, such as show run, which is the most basic troubleshooting command.However, the command cannot be executed when your user level is at 0-14. You can assign permissions to these users using the following command:Privilege EXEC l

customized within a Network as needed without application. In the network, computers communicate through internal IP addresses. When the internal computer needs to communicate with the external internet, the device with the NAT Function (such as a router) converts an internal IP address to a valid IP address (that is, the requested IP address) for communication. 　　 2. NAT application environment 　　　　 Scenario 1: an enterprise does not want external n

Update the public ip address of the Cisco router. First, confirm how your network is going. Here we will talk about the configuration based on our network: first, remove the default route no ip route 0.0.0.0 0.0.0.0 xxx. xxx. xxx. xxx adds the new default route www.2cto.com ip route 0.0.0.0 0.0.0.0 xxx. xxx. xxx. xxx then remove the ACL to overwrite the no ip nat inside source list 1 pool BJ. RK overload re

Cisco router nat translation 1. One-to-one correspondence between the internal address and the egress address disadvantages: When the egress address resources are scarce, only a small number of hosts can be connected to the internet. 2. The internal address shares the egress address. The router uses the egress address and port number, as well as the external host

There are too many Qos information on the Cisco Router Traffic Control instance, but many of them are not practical. I have talked about a lot of theories. The following are the configurations on the routers of a subsidiary for your reference. In fact, as long as you understand the meaning of NBAR, CBWFQ, and WRED, traffic control can be configured as needed. Www.2cto.com Description: A subsidiary uses a 2

When we use Telnet to log on to the device, the user name and password are transmitted in clear text, in order to ensure the security of the data, we recommend the use of SSH login device. The following is the configuration of the Cisco router SSH:1. Configuring hostname and Domain-nameR1 (config) #hostname R1R1 (config) #ip domain-name frame.com2. Generate the key, here is the 1024-bit key, the key length

The port Mapping method enables access to specific port services from the Internet to the local area network internal machines. For example, the machine you are using is in a LAN connected to the Internet, all the services you open on the machine (such as FTP), by default, the outside world can not access. This is because your IP is the LAN internal IP, and the outside can access only the server you are connected to the IP, because the entire LAN on the Internet only a real IP address, and this

Cisco 7609 Router boot rommon modeCisco7609 boot into Rommon 1 > Mode solution:Rommon 2 > Dir disk0: Check if the file existsInitializing ATA Monitor Library ...Directory of Disk0:2 120962020-rw-c7600s72033-advipservices-mz.122-33.src3.binRommon 3 > Confreg 0x2102 Correcting register valuesRommon 7 > Boot=disk0:c7600s72033-advipservices-mz.122-33.src3.binRommon 8 > Sync SaveRommon 9 > I restartThe above ope

successfully and you can view your saved files on the TFTP server.4. Restore your configuration file, ping the TFTP server, keep the connection, download from TFTP to the routerCopy tftp running-config Download the previously configured backup from TFTP and restore the router's configuration fileIP address of the 192.168.1.1 TFTP serverRUNNING-CONFIG-BK you want to restore the backed up files in TFTPRunning-config a name for your recovered files.Final reload, successful restart, successful reco