The naming rules for Cisco switches are more complex than the naming rules for routing,Look at these:ws-c2960-24tc-l, WS-C2950G-24-EI-DC, Ws-c2960-24tt-l, Ws-c3750g-24ts-e, Ws-c3750g-24t-s, We didn't find them on the switch, we just saw the Catalyst 2950 series and wrote it all: The Cisco Catalyst 2950 Series, which means the
#config terminal
Route (config) # line vty 0 4 ---- enter telnet remote login port mode (0 4 allows 5 Users)
Route (config-line) # password CISCO ---- set the password to "CISCO" (to encrypt the password, enable vro password protection before: service pass-encryption)
Route (config-line) # login ---- encrypted upon login
Route(config-line)#exit
Continue to enter the privileged mode and wh
Company a device, Ws-c2960s-24ts-l, is the Cisco 24 Port 1000M Two layer Exchange Yang, the use of iOS version of 12.2 (UNIVERSALK9-M) iOS software, the company recently installed some digital cameras, The monitoring host and a billiard-type monitoring to the machine, the interface of the transmission rate is much larger than the rate of ordinary office, the following is the rate of the two interfaces I copied.G1/0/3 (Monitoring host interface)5 minut
Cisco mds9222i Fibre Switch most commonly used debug commands1. Check the switch portShow interface [Interface-range]View specified port run status, WWN information, configuration parameters, and packet statistics.Demonstration:mds9222i-1# Show Interface FC1/1FC1/1 is trunking-port FC1/1 operating normally, is a TE portHardware is Fibre Channel, SFP was short wav
First of all, the Cisco, the orders are not many, are basic. Not including STP, upgrades, Acl,web and the like.Ruijie and Cisco 99% are similar.CISCO layer-2Switch>go to HyperTerminal console switch>Enable access switch privileged mode switch#configure terminal Enter
The detailed steps for restoring the password of a Cisco switch are illustrated. If the password of a Cisco switch is improperly restored, the password will be lost. Today, we will contact the steps for restoring the password of a Cisco
CISCO router device categoryThe name rules of cisco routers start with cisco, such as cisco2611 and cisco2610. cisco is the name of the device manufacturer, 26xx represents the 2600 series routers, and xx is a more detailed classification. The following lists several common series of
The article I want to share and configure VLAN on Linux through Cisco Catalyst Switch.Requirements:1. Linux installed on a PC with one or more NICs (Network Interface Card). I Use the Centos 5.4 using 2.6.18-164.11.1.EL5PAE kernel. It should is applicable on other Linux distros such as Slackware, Ubuntu, Fedora, Debian, etc.2. Cisco Catalyst Switch 29503.2 Pc/lap
Port security Configuration for the Cisco PT Simulation Experiment (7) switchExperimental Purpose : Master the port security function of the switch, control the user's secure accessExperimental Background : The company network adopts the personal fixed IP Internet program, in order to prevent the company internal User IP address borrowing, using, unauthorized access to the
Common commands for Cisco switches -- set the switch Password
A. Change the remote TELNNET Password
Switch#configureterminal
Switch(config)#linevty04
Switch(config-line)#passwordqycx123
Switch(config-line)#l
Cisco switch initialization ManagementTo properly manage and simplify troubleshooting, the following parameters should be configured during initial installation: 1. system name 2. manage ip configuration 3. clock and ntp settings 4. telnet and SSH access configuration 5. DNS6. system log 7. snmp is used to configure the switch system name on the
In the middle of a Cisco switching network, how do I find out which port of the switch is connected to the IP address of a machine? The most convenient and quick way is to use the User tracking function of the CiscoWorks 2000 LMS network management software. The graphical interface is clear at a glance.
If you do not have this software, you can use the following manual analysis method to find the answer:
Ex
Cisco switch Security Lecture Hall: cracking the shock wave virus and the red code, understanding the basic virus principles, and providing a good awareness of cisco switch security. Simple security measures will also receive attention. In today's online world, security is crucial.
As the Internet has brought huge bene
In a Cisco switch, how does one configure QOS speed limit? How to restrict BT download? This blog will use detailed examples for your explanation.
Instance 1: QOS speed limit problem on CISCO switches
It is used to control the bandwidth of a leased line user on a vswitch. The vswitch is usually at 10/100/1000 or three rates. QOS is required for other rates. You c
Cisco switch,
Cisco switchesSwitch> enable
Switch # con
Switch # conf
Switch # configure ter
Switch # configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--Cisco Internetwork Operating
): can only receive or send bpdus messages
learning (learning) : can receive or send BPDU Message, and form mac
forwarding (Forwarding) : can receive or send BPDU Message, and form mac Address table, send and receive data frames simultaneously
STP Convergence: All ports on the switch are converted to forwarding or blocking mode, which takes 50 seconds by default. The
)
--------------------------------------------------------------------------------
Add Catalyst 5002 to the domain
You need to add Catalyst 5002 To The VTP management domain named cisco and set it to VTP client. It will receive VTP configurations and updates from the VTP server.
Note: by default, the Catalyst 5000 series switches are VTP servers.
Cat5002> (enable)
Cat5002> set vtp domain cisco mode client
T
Tags: Cisco MDS zone san Configure a Cisco MDS Optical Fiber storage switch (MDS multilayer Director Switch multi-layer optical fiber array switch)General process: 1: Create a vsan, add the port to vsan2: create a zone, add the port to zone3: Create a zoneset, add the zon
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.