cisco ssh configuration example

It's classic. I use it.DeploymentsThe deployments in this document were implemented in an isolated lab environment. the deployments were cleared by issuing the write erase command on the routers, and the clear config all command on the switches to ensure that all devices have a default configuration. make sure you understand the potential impact of any configuration or command on your network before using i

~/.rhosts or/ETC/HOSTS.EQUIV for certification after the RSA certification is successful.For security reasons, it is recommended to use the default value of "No".RsaauthenticationWhether to allow the use of pure RSA public key authentication. For SSH-1 only. The default value is "Yes".ServerkeybitsSpecifies the length of the temporary server key. For SSH-1 only. The default value is 768 (bits). The minimum

management address, which is disabled by default and needs to be opened manually. The permission levels on Cisco devices are from 0 ~ 15. The default Telnet mode is 1, and the maximum permission is 15. (Privilege level [0-15]) The login function is enabled for the vty line by default, which means you must set a password for it to log on. Password 7 ***** cannot be used to set plain text. For example, if yo

With the development of the routing industry, the market demand is more extensive, but many users still do not understand the routing configuration issues. Here we mainly provide a comprehensive description of the Cisco router NAT configuration. More and more INTERNET resource sharing methods are available. In most cases, ddnleased lines are widely used with thei

#config terminal Route (config) # line vty 0 4 ---- enter telnet remote login port mode (0 4 allows 5 Users) Route (config-line) # password CISCO ---- set the password to "CISCO" (to encrypt the password, enable vro password protection before: service pass-encryption) Route (config-line) # login ---- encrypted upon login Route(config-line)#exit Continue to enter the privileged mode and wh

[Hkey_local_machine\software\cygnus solutions\cygwin\mounts V2\/home] "Native" = "d:\\openssh\\home" "Flags" =dword:0 000000aChange "native" to your own home/home directory, this directory is the default login directory, the default login directory is: C:\OpenSSH\homeEnter the following command to start the service:net start opensshdHere to show that the server has been installed successfully openssh and successfully opened the service, it should be pointed out that some of the above are in the

can run normally. However, it makes sense to rename a vro and uniquely identify it. Example: Router (config) # hostname Router-Branch-23 In addition, you can configure a domain name on the router so that it knows which DNS domain it is in. Example: Router-Branch-23 (config) # ip domain name TechRepublic.com 3. Set a password for privileged Mode When talking about setting a password to enter the privileged

Struts2 Based on the ssh (sturts2_spring_hibernate) framework and sturts2 configuration in ssh integration 　　　　　　　　 I. Logic of struts2 complete process (overall overview) First, the user enters the access path of your project in the address bar, and then the request is sent to the server, and then the server finds it in the web. A filter is configured in xml,

The following is a brief description of the configuration steps of 5505:1. Supervisor Engine Software Configuration:First, the Supervisor Engine Module needs an in-band (sc0) interface IP address, which is a manageable address and can be managed by telnet or SNMP for 5505. There is also an SLIPsl0 interface, which is not commonly used and is not described here.The default IP address of sc0 is 0.0.0.0, which belongs to vlan1. VLAN1 is the default VLAN

The Cisco 2511 router configuration method is used as a port device to connect to the WAN. The router has been widely used. Its main function is to connect multiple independent networks or subnets, achieve optimal path finding and data transmission between the Internet. This article takes the Cisco 2511 vro as an example