cisco switch reboot command

Cisco switches enable port speed limiting As shown in, Node switch 3550 is placed in an office room. The networks of all office companies are from this place. How does the operator configure network bandwidth settings for each company on this device? Let's take the IT Training Center of XX foreign companies as an example. The IT Training Center of XX foreign companies applied for a 2 m link. Step-1 Rongxi

[Cisco] DHCP relay, layer-3 Switch VLAN Routing PracticeThe experiment topology uses the GNS3 0.8.6 simulator to build a DHCP server using Red Hat 6.5. The experiment requires configuring a layer-3 Switch VLAN routing so that VLAN10 and VLAN20 members can access each other. Performs DHCP relay for layer-3 switches so that VLAN10 and VLAN20 members can obtain IP a

For complete syntax and application information about this chapter, seeCatalyst 3550 Multilayer Switch Command ReferenceAnd Cisco IOS Interface Command Reference For Release 12.1. Understanding Interface Types This section describes different interface types and some reference content for configuring these interfac

After the FLASH space is insufficient, I specially query the hardware configuration of the 6509 core device. The default Flash of the 6509 standard configuration is 64 MB, and the standard IOS size is 32.1 MB, the IOS 12.2 (17a) SX version to be upgraded has a size of 40.6 MB. In this case, it seems that the space is insufficient. However, this problem is well solved. The original IOS in Flash is deleted and then uploaded. So enter the command: Router

Tags: instance blank color 5.0 Ted Add dot1q message htmlTest topologyEnvironment: DHCP server and client are in different network segmentsConfiguration of DHCP serverNo IP routing IP dhcp pool vlan27 172.28.27.0 255.255.255.0 172.28.27.254 172.28.28.15 172.28.28.16 172.28.28.254 configuration of the L3-switchinterface Vlan27 IP DHCP relay information trusted172.28.27.254 255.255.255.0 IP helper-address 172.28.28.253 Access Switch configurati

protected] bonding] # ethtool EM2Settings for EM2:Supported ports: [TP]Supported link modes: 10 BaseT/half 10 BaseT/full100 Baset/half 100 Baset/full1000 Baset/fullSupports auto-negotiation: YesAdvertised link modes: 10 BaseT/half 10 BaseT/full100 Baset/half 100 Baset/full1000 Baset/fullAdvertised pause frame use: NoAdvertised auto-negotiation: YesSpeed: 1000 MB/SDuplex: fullPort: Twisted PairPhyad: 1Transceiver: InternalAuto-negotiation: OnMDI-X: UnknownSupports wake-on: GWake-on: dLink detect

Experimental requirements: Use Telnet login to complete the initialization configuration of a switchTopology diagram1. Enter the command line of the switch2. Enter enable into privileged mode3. Enter configure terminal into global mode4. Enter hostname Ruan Change host name to Ruan (here the hostname is just as good as you remember)5. Enter enable password 1314 to set the plaintext management password to 13146. Enter enable secret 520 to set the encry

The topology diagram is as follows:650) this.width=650; "src=" https://s2.51cto.com/wyfs02/M01/9D/77/wKiom1mAbhHgLT-uAABkvE_XhAg204.jpg "title=" 1.jpg "alt=" Wkiom1mabhhglt-uaabkve_xhag204.jpg "/>Description of the above equipment use:1, using R1 to do DHCP server2, use R2 and R3 instead of computer to do DHCP client3, SW1 used as a fool switch.DHCP server configuration (R1 configuration):r1#disable############ #使用 disable Command exit privileged mode

) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/82/A7/wKiom1deJrHCVwtlAADCdOtwrPQ145.jpg "/>650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/82/A6/wKioL1deJ8Ly_3SlAAB3c1VnNiQ372.jpg "/>Test if NTP synchronization is available on another LinuxCommand:Yum Install NtpdateNtpdate 172.31.251.196650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/82/A7/wKiom1deJrKwy7tMAAA60-x1dao326.jpg "/>Iv. Synchronization of SwitchesConfiguration command:Conf tNTP server 172.31.251.196650)

A Dell machine with a network card of M is connected to a Cisco switch. The error err-disabled occurs because of link-flap, that is, the network card is up and down too frequently in a short time. This error is not returned when a vswitch interface is changed. The cause is unknown. Link-flap description: Link-flap Error Link flap means that the interface continually goes up and down. the interface

Restricting Server Downloads:Speed 10Srr-queue Bandwidth Limit 50 (at this time the server download is limited to 10M 50 that is 5M)Speed 100Srr-queue Bandwidth Limit 50 (at this time the server download is limited to 100M 50 that is 50M)Obviously this speed limit download command is in line with the port protocol in useLimit server uploads: (If you want to limit upload download to 10M, direct speed 10 OK)1. Start QoS on the switchMLS QoSTo start QoS

displayed. Some people think that this Cisco router mode is useless because configuration changes cannot be made in this mode, and users cannot view any important information. 2. Privileged mode router # administrators can view and change configurations in this mode. I believe that it is absolutely important to have a set of passwords at this level. To switch from user mode to privileged mode, the administ

In Cisco command configuration tip 1, we talked about using the Range Command to simplify our configuration. However, if we often operate on a group of discontinuous ports Such as interface-range fa1/1, fa1/3, fa1/5, fa1/7, fa1/11 Even using the Range Command is cumbersome. We always think that the simpler