cisco switch vlan configuration step by step pdf

Technical standards for VLANs IEEE 802.1Q was formally promulgated by IEEE Commissioners in June 1999, and the earliest Vlna technology was proposed by Cisco (Cisco) companies in 1996. With the development of the past few years, VLAN technology has been widely used in large and small enterprise networks, becoming the most popular Ethernet LAN technology at presen

to say, after you set the password for level 1, you will be asked to enter the password next time you connect to the switch and enter K, this password is the password set for level 1. Level 15 is the privileged mode password that you enter after you enter the enable command. Step 2: Set the VLAN name. Because the four VLANs belong to different switches, the comm

-if) # channel-group 1 mode desirable Switch (config-if) # end Appendix: Switch (config-if) # channel-group port_channel_number mode {auto | desirable | on} // Add the physical port to an Ethernet channel and determine the PagP mode. 3) layer-2 Ethernet Channel Configuration Switch # configure termina

domain COM settings vtp admin domain name com PAR2 (VLAN) #vtp client to set the switch to clients mode Par3#vlan database into VLAN configuration mode PAR3 (VLAN) #vtp domain COM settings vtp admin domain name com PAR3 (

Branch switches.The Cisco switch can support any media as a trunk line. To achieve relay, you can use its unique isl tag. Isl (inter-switch link) is a protocol for transmitting vlan information and vlan data streams between switches, between switches and routers, and betwee

the ports of the corresponding vswitch as required in table 1. To verify our configuration, you can use the show vlan command in privileged mode to display the configuration you just made and check whether it is correct. The above describes the VLAN configuration of the

Lab Environment:650) this.width=650; "alt=" Cisco Packet Tracert three-tier switch VLAN configuration-Ibm.chick-mingkang.zhou "src=" Http://img2.ph.126.net/2N Qfixjyba1gdiqtbuknhq==/6630601572768576164.png "style=" border:0px;height:auto;margin:0px 10px 0px 0px; "/>Experimental Purpose:1, the three layer

192.168.3.0, The subnet mask is 255.255.255.0, And the Gateway: 192.168.3.1 is named work01, vlan4 is the network of client 2, work02, IP address segment is 192.168.4.0, subnet mask: 255.255.255.0, Gateway: 192.168.4.1. 3550 Ports 1-8 are allocated to VLAN 2, ports 9-16 are divided into VLAN 3, and ports 17-24 are allocated to VLAN 4. To configure DHCP for a

Lab Environment:Routers make Tp-link set up NAT forwarding, Tp-link router gateway is set to 192.168.30.254 ( core layer) Cisco 35,503 layer switch (model C3550-I5Q3L2-M) configuration three Vlan,vlan 10, VLAN 20, and

Droppe d:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Until This step, creating and configuring VLANs has been done on the Linux box. Now we is going to configure VLAN and trunk on the Cisco Catalyst switch

that the admin domain is able to overwrite all branch switches. The Cisco switch is capable of supporting any media as a trunk, and it can use its own ISL tags for relaying. ISL (Inter-Switch link) is a protocol between switches, between switches and routers, and between switches and servers to transfer multiple VLAN

I am eager for the first time to switch between vlan routing and nat addresses of Cisco switches. I am very energetic and have an undefeated spirit. I am ready to continue to answer questions during multiple rounds of interviews. My little brother squashed his eyes and took out the bottom of the press box: If my company has two Internet interfaces, A and B, respe

I. Demand1, divide three VLAN VLAN2 Server 1-8 Port Network VLAN3 work01 9-16-Port Vlan4 work02 17-24-Port 2. Gateway Configuration 192.168.2.1/24 192.168.3.1/24 192.168.4.1/24 3, DHCP and reservation Each section to open DHCP, each reserved xx.2-xx.10 segment IP for reserved use 192.168.2.10/24 for AD domain server, concurrently as a DNS server, plus two additional alternate DNS 114.114.114.114 8.

Cisco switch vlan division // Add vlanSwitch> enableSwitch # vlan dataSwitch (vlan) # vlan 10 name v1VLAN 10 added: Name: v1Switch (vlan) # vlan