Vswitch Virtual Network (Virtual LANs) settings:VLAN division and external VLAN routing settings on Catalyst 5000Assign a VTP Domain)Add Cat5000 to the domainSpecify the relay port (a Trunk)Dynamic ISLAllocate VLAN to PortSet VLAN 20Configure the RouterNote: There are three VLANs, which are routed between VLANs through the Router.-Allocate VTP DomainsWhat is VTP?VTP is short for VLAN Trunk Protocol. It provides each device (router or LAN-switch) to send broadcasts on the trunk ports. these broad
Cisco Wireless AP Configuration Guide requirements in complex enterprise environments Overview: using Cisco AP to build an enterprise wireless LAN, users' laptops do not need to be added to the AD domain,You can log on to the wireless network. the user name and password of the domain are used for Logon. SSIDS hides the password,Therefore, you cannot select the SS
I. Basic configurations of Cisco 2950 vswitches
Switch>
Switch> enable
Switch #
Switch # vlan database (entering vlan maintenance mode)
Switch (vlan) # vlan 2 name vlan2 name vlan 2 vlan2)
Switch (vlan) # vlan 4 name vlan4 name vlan 4 vlan4)
Switch (vlan) # exit. Note that exit is valid only when exit is enabled. You cannot exit directly with ctrl + z or end because the configura
CISCO PT Simulation Experiment (4) VLAN partitioning and configuration of switchesExperimental Purpose :Master The basic configuration of virtual LANs (VLANs);Master the configuration method of switch port VLAN and tag VLAN;Master the configuration method for VLAN trunking (
I came back again, the last two articles introduced the Huawei Stack, third firewall IRF. This time to introduce the Cisco stack (stack), although the implementation of the idea is consistent, but the configuration there is a need to pay attention to the place, especially now do the two-tier operators of the network workers, all the producers will be, the pressure is really big.First, the topological enviro
In Cisco router configurations, NAT configurations are frequently used. I hope the introduction below will be helpful to the majority of fans. It is a common method. The vro performs simple NAT translation and sets a CIDR Block in the NAT address pool. After a while, I found that the address pool was a waste of time. When I wanted to use a real ip address, I couldn't use it, so I decided to modify the Cisco
CISCO mds FC optical fiber switch configuration reference(1) There are several concepts that must be clarified (different from brocade ):(1) brocade divides zones directly. While mds divides zones under vsan, mds can divide several vsan first, and each vsan includes several zones.(2) brocase: the default port is open, while the default port of mds is closed.(3) mds has a Default zone: "The Default Zone ". i
Basic configuration and management of the Cisco PT Simulation Experiment (1) switchExperimental Purpose : Master the basic configuration and management of the switch, and understand the basic commands of the switch configuration. Experimental background : A company has a new batch of two-layer switch, before formally p
This article uses the Cisco 2509 Terminal Server to log on to other machines. how to configure the server? The following article describes the configuration process in detail and provides configuration commands.
Use Cisco router reverse Telnet for Terminal Server
If we have multiple routers for experiment, it will be
asked the boss, and he did not know it. It is said that the password was changed by the supplier. So the phone supplier asked the password for a long time and got a reply: at that time, the changed employee quit, and now he does not know the password .... dizzy .. too irresponsible .. there is no way to ask for your own, for your own, for google... (Although I have learned how to restore the password of a Cisco router before, but the vswitch and vro
Routers are packet forwarding devices that work in the third layer of the OSI Reference Model-the network layer. Routers implement network interconnection by forwarding packets. Although routers can support a variety of protocols (such as TCP/IP, ipx/spx, AppleTalk, etc.), most routers in China run TCP/IP protocol. Routers typically connect two or more logical ports identified by an IP subnet or Point-to-Point protocol, with at least one physical port.
The router determines the output port and t
the ports of the corresponding vswitch as required in table 1. To verify our configuration, you can use the show vlan command in privileged mode to display the configuration you just made and check whether it is correct.
The above describes the VLAN configuration of the Cisco Catalyst 1900 switch. The VLAN
CISCO PT Simulation Experiment (15) loopback Telnet configuration for routersExperimental Purpose :Mastering the features and functions of router loopback interfaceMaster the configuration of the Loopback interface to achieve Telnet login to the routerMastering the basic configuration of RIP dynamic Routing and default
Q: Are there any simple tools and methods? Run the script automatically on N or so cisco switches according to the script, and then return the result?Method 1: Download and modify the vswitch configuration file and upload it to N vswitches. Restart or copy start run.Method 2: Create a bat file under windows. The content in the file is the same as the command you used to telnet to the vswitch for modificatio
Simple Local authentication:(config) #username admin password Cisco // Establish user admin password for Cisco Local User (default permission level is 1)(config) #line vty 0 4 (config-line) #login local / /call on- premises authentication / / above method configuration, the default entry is User mode ">" After Telnet, An en password is required to enter
In DHCP settings, we usually work with routers. Here we will introduce the debugging and settings of Cisco routers and DHCP. A company uses Cisco 3620 as the ios dhcp Server. the IP address of the fastethernet0 port connected to the Intranet is 192.168.1.4. The L2 Switch uses two Cisco 2950 and the L3 switch uses a Cisco
series, can support 3620, 3640, 3660, 7200 four kinds of equipment, at the same time solved some configuration, the CPU usage of the computer is 100%.
0.2.7-RC1 was developed by the author recently and many bugs have been fixed. This version adds 2600, Cisco 7200 NPE-G2, Cisco 7200 new Ethernet Port Adapters to the original supported devices.
The running method
Product introduction
Cisco SDM is an intuitive and web-based device management tool for managing routers based on Cisco ios® software. Cisco SDM simplifies the router and security configuration process through the Smart Wizard, and with these wizards for customers and Cisco
[CISCO] NAT configuration full guide vronat NAT Function configuration introduction with the rapid development of the internet, the shortage of IP addresses has become a very prominent problem. A variety of solutions have emerged to solve this problem. The following describes an effective method in the current network environment: address translation (NAT. 1. NAT
unique.
Default route Configuration
The default route is generally used in the stub network, and the stub network is a network with only one egress path. Use the default route to send packets that are not included in the route table of the target network. In fact, you can understand the default route as a static route with a wildcard (wildcard.
Dynamic Routing Protocol configuration method:
IGRP dynamic Pr
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.