Test environment:
Cisco Router Intranet interface F0/1:192.168.1.1 255.255.255.0
External network Interface f0/0:10.0.0.1 255.255.255.0
Server ip:192.168.1.100
First configure on the router:
Router>en #进入特权模式
router#conf T #进入全局配置模式
Enter configuration commands, one
255.255.255.0 IP nat outside no IP mroute-cache Bandwidth 2000 No Fair-queue clockrate 2000000 Interface Serial1 No IP address shutdown No IP classless IP route 0.0.0.0 0.0.0.0 Serial0 access-list 1 Permit 10.1.1.0 0.0.0.255 Line con 0 line aux 0 Line vty 0 4 password Cisco End 3, multiplex dynamic address conversion applicable environment: Dynamic Address Translation is a dynamic address conversion, but it can all
The company's GPS patrol system needs to go WVPDN to communicate, but before looking for a telecommunications took a CISCO2811, collapsed once, the 2811 is the telecommunications sent, the estimated quality is not how, and then to find the company to buy the same type of equipment, 2811 discontinued, on the Cisco 2911.Yesterday arrived Ah, excited a bit, super terminal connected on, looked at the system configuration, the result of the hand is cheap,
Cisco routers are widely used in network interconnection. Among them, 2500 series routers are widely used in low-end users. So what if you accidentally forget the superuser password of the 2500 series router? Don't be afraid, as long as you can restore as follows:Preparation: a computer running Terminal simulation program can start a Super Terminal in Windows 95/98), and the microcomputer serial port COM1/C
The Cisco router NAC solves the problem. The so-called NAC is an architecture that allows multiple hardware and software components to work together to protect the user's network from adverse client attacks. 1. It is not easy to fully implement NAC, because the entire architecture contains too many different components from other vendors. For example, the architecture contains the NAC Policy Manager and mul
When a Cisco router forgets or loses the enable password, there are two ways to recover, depending on which series of routers you are using.
The first of these methods
This approach restores the following routers: Cisco 2000 series, 2500 series, 3000 series, Cisco 4000 series using the 680x0 Motorola CPU, and 10.0 se
:(1) Step 1: Configure the Router Ethernet interface IP address(2) Step 2: Configure the router password(3) Step 3: Access the router via TelnetCommands for the relevant steps:Configure the Router Ethernet interface IP address (enter the privileged mode, global mode, interface mode, and configure the Ip-> activation in
Article Title: simulate a cisco router using dynamic in Linux. Linux is a technology channel of the IT lab in China. Includes basic categories such as desktop applications, Linux system management, kernel research, embedded systems, and open source.
Environment: centos5.2
Software: dynamic. cisco-ios
1: Download the dynamic binfile.
Wget http://www.ipflow.utc.fr/
Cisco router Tcl script backdoor 2nd tests
Author: Vic
The security of Cisco routers is certain. Password verification is required for remote login. The Cisco passwords are encrypted in the following ways:1 not encrypted, plaintext display
650) this. width = 650; "border =" 0 "alt =" "src =" http://img1.51cto.com/attac
CISCO Router Network Address Translation (NAT)Tutorial name: Cisco Router Network Address Translation (NAT) objective: to connect all Intranet IP addresses to the Internet using a small number of public IP addresses. Tutorial Introduction: using NAT technology, when an intranet private address sends data packets to a v
Tags: Cisco CCNA router Password managementfor device security, the device administrator typically sets the user name and password for the device. Here's how to configure 3 passwords, with emphasis in the middle.Username Test password Cisco//This is to set up a layer of accounts and passwordsEnable password 123// This is the Setup admin passwordRouter (config) #l
Cisco port status: CSU ── channel server unit, DSU ── data server, unit, DTE ── DataTerminalEquipment
1. Serial * is down, line protocol is down (DTE) faults:
[1] No power is added to the vro.
[2] LINE is not connected to CSU/DSU.
[3] hardware error.
Solution:
[1] Check power supply.
[2] Check whether the cables and serial ports used are correct.
[3] switch to another serial port.
2. Serial * is up and line protocol is down (DTE) faults:
[1] local or
Tag: Register BRE router exists reload conf device star RAMClear the password for the Cisco 1841 router:(1) The console line connects the computer and the router console port, through the terminal client connection, the router is powered on (if the device is started, press t
A Cisco router is detected infected with a secret backdoor.
Security company FireEye researchers reported that backdoor programs called SYNful knock were found on 14 Cisco routers in 4 countries. Cisco has confirmed this. The attack does not take advantage of the vulnerability of the product itself, but requires valid
Global debugging
When configuring a Cisco router, the boundaries between global and interface commands are obvious. In this case, we use "Global" to identify commands that cannot be used for interface debugging or specific transmission media types and Protocol debugging. For example, in vrouters 2500, you can use Debugging commands to analyze the Cisco Discovery
RIP and IGRP are commonly used router configuration protocols. What problems should we pay attention to when configuring RIP and IGRP? What should we do? The following configuration steps provide detailed answers.
RIP Protocol
RIP (Routing information Protocol) is an Internal Gateway Protocol (IGP) that is widely used earlier and is suitable for small-sized similar networks, is a typical distance-vector protocol. For more information, see RFC1058 an
. RPF reverse transmission path forwarding) is an input function activated on a network interface or sub-interface to process packets received by the router.
It is very important to enable the CEF function on the vro, because RPF must rely on CEF. Unicast RPF is included in Cisco IOS 12.0 and later versions that support CEF, but does not support Cisco IOS 11.2 or
1. Preparation Tools
Cisco TFTP server, HyperTerminal, iOS files
iOS files are not easy to find, you need to look at the hardware version, as well as the size of ROM RAM, to my Cisco 2621XM for example (with two fastethernet),Start looking for a few 2600 of iOS, the brush is not correct, the problem of unrecognized network interface, can not be configured, there should be F interface with S Ios,
CHAP (Challenge Handshake Authentication Protocol) and PAP (Password Authentication Protocol) are generally used to provide security Authentication on PPP encapsulated serial lines. With CHAP and PAP authentication, each Cisco router is identified by a name to prevent unauthorized access.
Task commands
Set the PPP encapsulation ppp1
Set the authentication method ppp authentication {chap | chap pap | pap cha
This article describes how to control the BT traffic of a Cisco router through specific operations, and describes the specific operation methods in detail. I hope this article will help you.
Network-Based Application Recognition (NBAR) indicates Network Application Recognition. NBAR is a technology that can dynamically search for protocols in Layer 4 to Layer 7. It can not only control static and simple net
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.