cisco vrf configuration

This site has previously shown us the method of segmenting a router into eight virtual routers using virtual Routing and forwarding (VRF, VM forwarding) through a scene example. I showed you how to configure VRF, and in this article we continue to use this scenario and, through IPSec configuration, replicate the exact topology and address to eight experimental en

With the rapid growth of network infrastructure construction, the link technology of wide-area private networks in various industries has also undergone major changes. Traditional wide-area private networks are generally implemented by renting point-to-point long-distance ddnleased lines. problems such as long construction periods and difficult maintenance exist. With the popularization of MPLS technology, bgp mpls vpn technology solutions have become one of the most popular VPN solutions. Gener

######## Snmp-server host 50.1.50.3 use-vrf default udp-port 9006 // The default port is the Management port of the Engine board to send packets. You need to configure this command when sending packets to the business line interface. Cisco (config) # int e1/1 Cisco (config-if) # no snmp trap link-status // ignore the up-down information of the port, not trap to

LAN is not changed, and the configuration and access control list of the external network Port WAN needs to be changed .Increase the configuration of the VPDN. Assuming the username is admin, password 123456, the configuration process is as follows:This case is XX Telecom ADSL PPPoE access, need to use a common ADSL modem and a

Cisco configuration instance _ Cisco dual-Egress NAT configuration objective: to simulate the routing function based on the original address policy when a dual-Egress link is available, and access to the external network from different original addresses is realized, in most cases, the vro uses NAT to translate the Int

Introduction to CISCO router AAA and related routing configuration cisco aaa www.2cto.com 3A concept: authentication authorization Accounting accountingcisco provides a variety of 3A services for routers and switches: 1. Self-contained AAA router/NAS self-contained AAA service NAS (Network Access Server) 2. Contact the AAA service on the

Previous page Everyone talked about Cisco Basic Operation command switch, while dragon boat holiday, the Cisco simple switch configuration, and hope you share "Happy Dragon Boat Festival"! Ok, configure the switch, first, you must enter the global configuration mode switch, successfully connect the switch and landing s

(Config-router) #exitIf this is all configured, then use the ping command to test it!Here is a start-up-configuring HSRP Hot Spares:Configure on the active three-layer switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.168.1.254Switch (config-if) #standby 1 priority 200Switch (config-if) #standby 1 track fastethernet 0/2Switch (config-if) #standby 1 preemptConfigure on the backup layer three switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.1

An example of Cisco Easy VPN comprehensive configuration is shown in this example. The topology is 15-15. In this example, the Cisco 831 router is used as the remote device of Easy VPN and the Cisco 1751 router is used as the device of Easy VPN Server. In this example, the WAN interface IP addresses of the

For Cisco Network Assistant (CNA), it is estimated that Cisco has launched a free tool that can be used to configure Cisco devices such as Catalyst switches, PIX firewalls, IP phones, and wireless access points, CNA support, As long as it is facing small and medium enterprises. CNA provides a number of features and wizards. The following figure: CNA provides

Basic configurations of Cisco routers and Cisco router configuration commands En -- enter the privileged mode config t -- enter the global configuration mode wr (OR) -- save the configuration (otherwise, the configuration fails be

Configuration example of cisco router and layer-3 Switch environment, cisco layer-3 SwitchSimple environment configuration instance for cisco router layer-3 Switch I. network topology: Ii. configuration command: 1. vro

Technical standards for VLANs IEEE 802.1Q was formally promulgated by IEEE Commissioners in June 1999, and the earliest Vlna technology was proposed by Cisco (Cisco) companies in 1996. With the development of the past few years, VLAN technology has been widely used in large and small enterprise networks, becoming the most popular Ethernet LAN technology at present. This article is going to introduce one of

, adding switches and end devices1, double-click switch into switch command line (CLI) mode, switch configuration mode by command2 in most cases for security reasons, you need to configure the switch privileged mode passwordValidation test3 Configuring the telnet login switchTo achieve remote login, first need to configure the login user and device management addressVerify the configuration by matching the

, 6800IA is restarting, patiently wait, and then observe.Router#show FexFex Fex Fex FexNumber Description State Model Serial---------------------------------------------------------------------------101 6800ia-48-01 Online c6800ia-48td foc2016s1ndAfter a wait, when you find that the status is online, that the 6800IA is connected to normal, you can configure it!We can see if the interface of IA is added by the show Run command.Router#show Run........................ Also omit the N-line

that the admin domain is able to overwrite all branch switches. The Cisco switch is capable of supporting any media as a trunk, and it can use its own ISL tags for relaying. ISL (Inter-Switch link) is a protocol between switches, between switches and routers, and between switches and servers to transfer multiple VLAN information and VLAN data streams, configured with ISL encapsulation via ports directly connected to the switch, The VLAN allocation a

(global configuration mode)S1 (config) #interface vlan 1 --Enter VLAN 1 PortS1 (config-if) #ip address 192.168.1.1 255.255.255.0 --Configure the vlan1 with an IP address so PC1 and S1 can ping interoperabilityS1 (config-if) #no shutdown --activating VLAN 1 PortS1 (config-if) #end --Return to privileged modes1#copy running-config startup-config --Save configuration (from memory RAM to hard disk NVRAM)s1#sh

; set the VTP domain nameSwitch (config) #vtp password; set the VTP passwordSwitch (config) #vtp mode server, setting the VTP patternSwitch (config) #vtp mode client, setting the VTP pattern11. Set the IP and subnet mask for the Cisco switchSwitch#conftEnter the default VLAN status:Switch (config) #int vlan 1Set the IP address and mask:Switch (config-if) #ip address 10.65.1.3 255.255.0.0To set the gateway for switch:Switch (config) #ip Defaule-gateway

Cisco SDM is a good tool for vro security configuration. It features easy to learn and allows users to easily complete vro settings. Cisco SDM is based on Cisco IOS®An intuitive Web device management tool developed by Software routers. It simplifies router security configurations through smart wizard, allowing customer

China Mobile's GPRS network uses the APN method to connect to the GPRS device terminal and communicate with the server through the APN. The customer purchased the Cisco 2811 router, and the mobile company needed to pull the optical fiber through the E1 port, I spent more than 1000 RMB with an E1 module. mobile companies are doing very poorly, and optical fiber connectors are not provided at all. I also bought a switch for xxrmb, after a successful cal