This article describes how to configure a vswitch for a CISCO 3550 router and how to configure access control for a MAC address.
In network management, users often encounter this situation: some users violate management regulations and modify their own IP addresses without permission to access restricted resources. Such behavior not only undermines information security rules, but may also cause network comm
Recently changed jobs, the company more than 40 people share a 20M bandwidth wireless network, the router for Cisco R2911. Boss, let me make a cacti to monitor Cisco routed network card traffic. The whole days can not get the SNMP data, finally to the routing permission to find that the last operation to the routing SN
At present, wireless router has become a home wireless sharing and Internet application of the mainstream, about the use of wireless router is also a lot of users are very interested in, we will pick some of the more representative of the
shown in Figure 1.
It shows that there are multiple wireless networks available, double-click Tp-link to connect to the wireless router, and then connect successfully.
(2) Open IE Browser, enter IP address: 192.168.1.1 (wireless router default LAN IP address).
(3) Login
multiple available wireless networks, double-click the TP-LINK to connect to the wireless router, then the connection is successful.(2) Open IE and enter the IP address 192.168.1.1 (the default lan ip address of the wireless router ).(3) log on to the
be managed. If yes, test the forwarding performance for 5 minutes. The notebook is connected to a Wireless Broadband Router with a pair of two meters away and is in the same CIDR block as the 1600T simulated host.
Function verification
Use Cisco ESR 10000 to simulate the real environment, verify functions such as PPPoE, and evaluate the functions of the
Cisco Route wireless layout skillsMany companies encounter periodic disconnection problems when using wireless networks. How should we solve this frequent disconnection problem? Next we will give you a detailed introduction.I. The first thing to consider is the laptop, which may be caused by network connection errors due to compatibility or driver problems of the
1. Configure the IP provided to you by the service provider for the Ethernet interface of the AP.Ap#conf TAP (config) #int F0AP (config-if) #ip add 10.48.2.154 255.255.0.0AP (config-if) #no ShuAP (config-if) #exitAP (config) #ip Default-gateway 10.48.0.12, configure the BVI interface:AP (config) #int BVI 1AP (config-if) #ip add 10.48.2.155 255.255.0.0AP (config-if) #no ShuThe VBI interface configures the IP address and can be configured via a Web page. The Web page access address is the address
ExploitationScriptConfigureCisco router configurationBefore that, you must specify the operations you want to perform, execute those commands, and then write scripts. I want to back up the running-configure configuration. Of course, the device has been configured and the tftp server is ready. The Cisco router configuration is as follows:
BT
For the wireless router settings has been a commonplace, but there are still a lot of friends can not be a good grasp, then this article for D-Link DI-524 wireless router settings Method for a detailed introduction. I hope this article will help you.
D-Link DI-524 wireless
the router work normally, you must download the new IOS to FLASH. If the FLASH space is large enough, you can save multiple IOS software and select the version of the system to use. In order to quickly recover after such a fault occurs, it is best to save the IOS software in a secure server for urgent use.
3) Common Faults and system defects of wireless routers
Like WINDOWS systems often suffer from viruse
The wireless router is transformed from the ordinary household type to the performance formidable wireless router? Yes, this is possible, and the method described in this article will also allow you to implement without spending a penny, but what is the first thing to understand here is the DD-WRT firmware? Here's to e
uppercase; otherwise, it cannot be started. Of course, you can also store it in the root directory of the E drive, F drive, or G drive, and make the appropriate selection at startup;Step 3: edit the boot. ini file in the System Properties of the control panel, and add a line in the file: WEP2 cracking the WEP-encrypted wireless router APC:/grbt3 = start backtrackSave and exit.After the settings are complet
This article describes how to set up a wireless LAN for a home. You can search a lot of articles on the Internet. These articles seem very good, not only the detailed process description, but also related images. The lessons learned are shared with you.
The wireless router uses NETGEAR WGR614 (54M is 802.11g), and the NIC is also 54M (the configuration is very sm
a wall or brick chimney, or the network cable is introduced into the building from the worst possible location. If, for some reason, you cannot place the antenna in the ideal central position, do not be disappointed. We will introduce other solutions later.
Now, please go to the office to find a good home for the wireless router. Avoiding corners (especially in old houses) is the first step, because the co
, indicating that data is being transmitted when the green indicator is flashing.
8. Description of the wireless router: Meaning of the back panel:◆ 7.5V1.5A DC power supply hole: power cord with DI-624 +,◆ One end of the power connector is inserted into the user's ac v power outlet,◆ The other end of the Small circular joint is inserted into the DI-624 + A 7.5V1
Yesterday the company bought a few Sonos wireless hifi equipment, beans need to test the effect.As a simple test, my structure is very simple, the router (firewall) comes out to pick up the Cisco switch, then boost and my controller (computer or phone) are on a VLAN, and then between boost and player through the grid wireless
This article describes how to set up a wireless LAN for a home. You can search a lot of articles on the Internet. These articles seem very good, not only the detailed process description, but also related images. Because of my career, although I used to pay attention to the wireless router configuration, I failed to follow the surface because I didn't have the ac
will weaken the signal as the signal passes through. In addition, do not put the router in the closet, bookcases or entertainment center is a good place to place the router inconspicuous.
Of course, the wireless router requires an AC outlet and a connection to your cable o
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.